Build List
-
Active Filters:
ac
C-beam Machine - Modesty
Modified C-beam Machine. Taller (30 cm) C-beam uprights in gantry, and longer 750 mm frame in Y direction. XL gantry plate on X (and Z?). Y will have additional 700 mm SBR16 rails as extra support and slightly raised bed to fit above stepper motor. Approx. machinable area of 370 x 370 mm.
My large machine 48 X 48
This machine is controlled by a Mach3 BOB. I USED Nema 34 stepper motors and a 3kw, water cooled spindle. I’m in the process of adding a vacuum table with 4 zones. I have an X-carve so I use Easel to create G-code for the large machine. I’m currently looking for a way to stabilize the Y-axis. It wiggles a little, so I want to add another linear rail high on both sides.
cnc back stop for brake press
back stop build
Build Author Ryan Lock Views 122990
WorkBee CNC Machine
The WorkBee is our latest CNC Machine and is a culmination of all our experience, feedback, and suggestions from selling the OX CNC Machine over the past 2 years. The WorkBee is capable of accurately cutting foams, woods, plastics or aluminum at depths greater than 25mm to 0.2mm accuracy or greater.
Build Author Mark Carew Views 252313
C-Beam® Machine - Plate Maker
This C-beam Machine is an in affordable CNC plate maker and 3D carving machine!
My ACRO Build
An ACRO laser put together with some repurposed and some new parts.
Denford CNC Resurrection
Denford CNC Mill Update
Build Author that-jim Views 41194
LINEAR RAIL SPHINX 55 (Blue OX plates)
Machine based on Sphinx 55 built with linear rails.
Build Author Cam Garrett Views 2175
Sturdy Motorized Photographic Copy Stand
i would like to build a sturdy motorized photographic copy stand. i have hobbled together a hand crank version using a used umbrella pole but it is not suitable as it is awkward and wobbly.
Build Author Jason Moore Views 9999
Lead1500 Plasma Table w/THC
lead machine plasma table with Black Box, and Torch Height Control
Build Author OpenBuilds Views 17592
BlackBox X32
The next level of CNC motion control solutions. Packed with advanced new features and built on the reliability of the proven BlackBox system
Build Author Jasont Views 2465
MY first CNC build
my first cnc build using the lead 1010 to build bigger and better!!
Build Author Ahmed Ibrahim Views 6360
Cairo Mini 3d-Printer
We are introducing the Cairo Mini 3d-printer! It’s a DIY fully Open-source Reproducible 20x20cm 3d-printer. The original goal of the Cairo Mini 3d-printer is to create a low-cost 3d-printer below 220$(3500 LE). That anyone can build with ease.
Build Author Glenn Weston Views 9208
"AcroCadabra" My Acro Laser built with my C-Beam XL
Well I built a C-Beam XL around a year ago, I am still learning things as I make stuff with it, it has been quite a wonderful learning experience. Now I have gained enough confidence and knowhow to Mill the required Plates to build an Acro Laser System using the Acro Laser Sketchup Model. I have pulled the Model apart in Sketchup, isolated the Plates and generated the G-Code to cut/Mill the plates. I have used Sketchucam to generate the G-Code. I Use Mach3 on my C-Beam XL to Mill.
My C-Beam build and modifications
Modified C-Beam which I plan to add a laser module and eventually convert to C-Beam XL size.
Build Author SOA Views 57690
GridBot Two: Powerfully Simple
Core XY, sensor-less homing, integrated camera, touch screen, pi, 32-bit controller, fast, quiet, beautiful prints. 300 x 300 x any build volume. Just change out the Z lead screws, rods, and four pillars. Total BOM around $700 USD. Build time around 6 hours.
Build Author Mark Carew Views 76534
OpenBuilds Workbee 1510 (60" x 40")
The OpenBuilds WorkBee 1510 - 1500x1000 Belt Driven CNC Machine
Build Author lekey Views 6363
Modular Desktop Vacuum Former
This is a small desktop vacuum former that can be connected to a shop-vac and an electric heat source (like a grill for instance). You can control the time each appliance stays turned on, and the vacuum is automatically turned on when the tray is placed on top of the model. The vacuum table is 20x20cm wide, and I've tested it mostly with 1mm thick PET sheets.
Build Author Johnny Reich Views 983
ProLight 1000 Mill Retrofit
Update a 20-year old bench top milling machine with OpenBuild Ecosystem electronics.
DIY Vacuum Hold Down table
A simple vacuum hold down/clamp set up using a 6hp canister vacuum.
HYDRA multi tool CNC , based on ACRO
modifying ACRO
Build Author Quentin Karmark Views 5545
Laguna Swift 4X4 CNC mill retrofitted with OpenBuilds
Used Laguna Swift 4X4 CNC mill with Water-cooled Spindle and RichAuto serial pendant retrofitted with OpenBuilds/Blackbox/Interface
Pick and place
Pick and place based on the Openbuilds ACRO 20x20
Prototype Rack-n-Pinion 4'x8'
This is a custom gear rack drive machine with a 4'x8' cut capacity.
Build Author theracermark Views 2763
Reviving the Origonal PhlatPrinter with BlackBox
Reworked PhlatPrinter Gen1 Adding dual nema 17s to all 3 axis Supprot for carriage to insure even dept cuts Lighting for view of cutting area
Black gear 1500X3000
My cnc update and rebuild.
Build Author Mike Campbell Views 9041
bor 454-D
A large format, modular, rack and pinion build designed around OpenBuilds components.
Build Author Mark Carew Views 1157075
OpenBuilds OX CNC Machine
OpenBuilds OX CNC Machine. A strong easy to build shop CNC router that can be sized to suit your needs. Many new features have been incorporated into the OX to make it a great router that is sure to inspire!
Build Author Jacob Christiansen Views 5190
ACRO 1010 with custom Z axis
This is my build for an ACRO system with a custom z-axis for changing z height for focusing or for adjusting depth when making multiple passes when cutting.
Build Author OpenBuilds Views 3315
Interface magnetic mount
A simple build that helps you to mount the OpenBuilds Interface to the front of your machine.
Build Author CNCGear Views 8407
The BlackBee CNC
Ball screw drive, linear rail CNC Kit
Build Author Kyo Views 22050
Sphinx 55
A Sphinx build to inspire and encourage all those who want to get started with cnc to check out Opensbuilds line of machine bundles and hardware.
Build Author OpenBuilds Views 22412
INTERFACE CNC Touch Control System
Super cool standalone Human-Machine Interface for controlling your CNC machines!
Build Author OpenBuilds Views 8781
Swing Arm
Simple Swing Arm Build for the Modular Table Series. Create a simple vacuum swing arm that swings over your machine keeping your vacuum hose and router cord, etc. up and out of the way
Improved CBM
Yet another build of an improved C-Beam Machine, improving stiffness, size, versatility, and strength without increasing costs much.
Build Author Stokrotka74 Views 5546
Racoon CNC
This is a Sphinx variation, aimed to minimize footprint and maximize workarea. Work in progress.
AcoustoPlot3D
The Sphinx has all the components I need, except it will need a taller vertical lead screw, the same length as the horizontal ones. It will also need legs. So I need to start with the Sphinx parts list, then make a few changes.
Build Author OpenBuilds Views 12298
C-Beam® Tension XL Linear Actuator
Bringing your lead screw precision and accuracy to new lengths using a simplistic tension system!
KRE CO2 2x4 Laser
Large Format CO2 Laser Cutter
Build Author Crazzy French Dude Views 3601
PeeNaPle_V1.4b
PeeNaPle_V1.4b is a BoB controller board for 3D Printers, CnC and cartesian machine, using the latest Teensy_4.1
My build
I am satisfied with my build and next one will be even better.
Black Box/ Power supply brackets
This items are so cool that they need to be together, so I decided to create brackets that connect both pieces together
Build Author Quinnthouzand Views 2631
Mustardo - The Mustard Bot
The goal for this bot is to lay down mustard on sausages and burger patties in a smooth and sexy way that looks good for the camera.
Tall OX
After completing a standard OX build, I found I didn't have enough Z-clearance and designed a set of taller gantry plates
Build Author OpenBuilds Views 5352
V-Slot Ventilator
The idea is to make a simple effective ventilator, studying the concept of using a simple push process with and actuator.
Build Author Tristen Poliseno Views 2007
Back and forth rail mechanism
I have the whole description and all the details in the "Body" section!
Build Author Joe F Views 6826
Rack and Pinion Cartesian Mill
This is a rework of a previous build I did on here, a mostly printed cartesian CNC. Initially intended to just be an update to that, but so many things changed including the linear motion and every single part has been modified significantly that I felt as though it deserved a whole new build.
Build Author Alexander Leiser Views 12735
Paintbot painting cnc
Custom painting machine in designed and wrote the software for. Paintings are with acrylic color on canvas
Z Axis for ACRO
Created a small Z axis for the ACRO motion system. I wanted to more easily adjust the height of the laser to accommodate various thicknesses of material, without having to manually loosen screws to adjust. Also wanted to be able to vary the height for multiple cutting passes on some materials. Try to stick to a similar aesthetic as the original ACRO system and plates.
Build Author Kenneth Witthuhn Views 7269
Openbuilds CNC (witthuhnCNC XKLBR-1S)
Based on the popular C-beam / V-wheel design, with the largest available work area, relative to machine size. Screw driven with anti-backlash, integrated drag chains, Carbon fibre gantry plates, Openbuilds BlackBox Controller (USB), Transformer & kill switches, with internal wiring, limit switches & Nema 23 motors.
Build Author Forestbird Originals Views 3704
Lead 1010 Build - Anything but stock.
This is a lead 1010 build that I wanted to have a little fun with. I purchased the whole Lead 1010 kit, and felt like studying a few shortcomings of the original to see if I can improve it or just have some fun with it.
Build Author Martin.Barfoed Views 4929
40x40 V-Slot Rod Type Linear Actuator
A Rod-type Linear Actuator based on the 40x40 V-slot profile
Build Author Mark Carew Views 102050
V-Slot® NEMA 17 Linear Actuator Bundle (Lead Screw)
Example model of lead screw driven actuators for your next project!
Acro 1010 with 10 watt Laser
Built a 32"x40" ACRO Kit for my 10watt Endurance Laser. Put it in a stand alone clamshell cabinet, added a 340cfm 6" fan and variable speed switch for the fan. Using LIght Burn for my primary software. It seems to be work well.
Plasma CNC machine
The plasma CNC that I have built has a water table that measures 1350mm x 650mm. The water is flooded onto the cut area while cutting and recycled around with a pump. This is to reduce smoke, cool the metal being cut to reduce distortion and also to keep sparks to a minimum. Most of the machine has been made from aluminium , the frame and table from steel, the water table, stainless steel.
Build Author David Florian Views 8262
Dual Extruders 3D Printer - Zidex Upgraded
How to build an Independent Dual EXtruder (IDEX) 3D printer from OpenBuilds parts.
Build Author Sonny Lowe Views 5173
MakerSL MSL-65 Manual Coffee Grinder Stand
I know this build is a little off category here at OB, but I wanted to share it with the community (as well as other coffee lovers) and show however vast the possibilities are when OB hardware is involved. This is a powered stand intended to operate a manual coffee grinder. It is compact, light, portable and uses simple drive components (B&D Cordless Screwdriver). I will post two version, V-1 (Beginner skill level ) and V-2 (Intermediate skill level). Both accomplish the same results.
Build Author Darren Dickson Views 3016
3D printed CNC Machine
So I thought I would make the Leon van den Beukel version three 3D printed CNC Machine, it is the third incarnation so you would expect a relatively bug-free CNC Machine with a strong foundation.
Build Author Mark Carew Views 47034
OpenBuilds Sphinx 55 (20" x 20")
The OpenBuilds Sphinx 55 - 500x500 Lead Screw Machine
Build Author Mark Carew Views 28774
OpenBuilds Sphinx 1050 (20" x 40")
The OpenBuilds Sphinx 1050 - 500x1000 Lead Screw Machine
Build Author Bruce Walker Views 5744
BD's Burn Box - ACRO Laser Engraver System
Two plus years in the making, I finally have a working ACRO 510 laser engraver system complete with enclosure and air filtration.
Build Author Fábio Pires Views 5928
Frezar - Desktop CNC
This is a small desktop CNC inspired by the Mini OX project. It's designed with the nema 17 motors in mind. It's a 650mm x 500mm machine that it will be used to mill cast acrlic.
Build Author Mark Carew Views 73466
BlackBox Motion Control System
The Openbuilds BlackBox is a new system evolved around a set of subsystems that cover more than just control and also more than just CNC type applications! With a plug-and-play easy connection system this controller can be used with ease, without sacrificing power.
Build Author Mark Carew Views 28235
High Z Mod for Lead CNC
The High Z modification for the LEAD CNC brings your creative capabilities to new heights! With 8" of clearance this modification can be adapted easily to your existing LEAD CNC Router.
Build Author Mark Carew Views 57300
V-Slot NEMA 23 Linear Actuator (Lead Screw)
Learn to build a super strong nema 23 lead driven linear actuator
Build Author Mark Carew Views 14188
Nema 23 Belt and Pinion Actuator
This easy to build and effective system can take your builds to the next level! This design is strong and accurate and could be the solution/upgrade that you've been looking for!
Build Author Mark Carew Views 18747
V-Slot™ Nema 23 Linear Actuator (Belt Driven)
This example build shows how easy it is to make a linear actuator using a few OpenBuilds Parts.
Build Author Mark Carew Views 19421
C-Beam® XLarge Linear Actuator
This OpenBuilds C-Beam XL actuator is the backbone of a lot of the awesome builds put together by the OpenBuilds community
Build Author Mark Carew Views 13246
C-Beam XLarge X/Y Table
This OpenBuilds C-Beam XLarge X/Y Table is a great display of how easy it is to modify and create awesome configurations with the OpenBuilds system!
Build Author Mark Carew Views 12358
NEMA 17 Belt and Pinion Actuator
This Belt and Pinion actuator is a great example of how easy it is to convert your machine into a belt drive system.
Build Author Mark Carew Views 10334
C-Beam® Double Wide Gantry Actuator
This easy to build actuator is configured to have not only strength, but accuracy! This low profile option offers endless possibilities, and we cant wait to see how this actuator is implemented in your build ideas!
Build Author Mark Carew Views 87760
V-Slot™ Mini V Linear Actuator
Learn to build the V-SLOT Mini V Modular linear Actuator System and create all kinds of cool machines!
Build Author Mark Carew Views 116975
C-Beam™ Linear Actuator
Here are a few helpful C-Beam actuator ideas that will help you get a start on your builds
Build Author tmadrms Views 5951
C-Beam Mods
C-beam machine mods.
Sim Racing rig
Made with OpenBuilds 2020 and 2060 material/brackets/hardware. Simlabs wheel deck. Fanatec DD wheel base/wheel/pedals NRG seat Sim racing studio wind simulators Few 3D printed brackets/caps/cable holds
Build Author Mark Carew Views 24226
OpenBuilds Workbee 1050 (40" x 20")
The OpenBuilds WorkBee 1050 - 1000x500 Lead Screw Driven CNC Machine
Build Author Mark Carew Views 68239
OpenBuilds Workbee 1010 (40" x 40")
The OpenBuilds WorkBee 1010 - 1000x1000 Lead Screw Driven CNC Machine
Build Author pedrofernandez Views 33913
Openbuilds Table Top 50w Co2 Laser Cutter/Engraver
DIY build of a Co2 Laser cutter/engraver 12x24 working area.
Build Author MattR Views 14527
Fixed Gantry CNC Router with Old Industrial Supplies
I got lucky enough to purchase aluminum extrusions and linear motion components (and nuts/bolts/etc) at scrap metal prices when a bunch of industrial automation equipment was decommissioned. The only problem is that the aluminum extrusions are not metric sizes... they are the 1.5"x3" 80/20 series. It has presented a few challenges but nothing too bad.
Build Author mjenkins5720 Views 1899
Modified LEAD machine
At the moment this build is in progress, I will be updating the files as I finish the remainder of the machine. This machine is intended to be a multipurpose CNC, but a bit bigger than a desktop unit. The machine is scalable in the X and Y axis.
Build Author reef Views 10293
CNC Cyclone PCB Factory, my way, step by step.
I'd like to renew my cnc for PCB so I decide to create new one from an existing project named Cyclone PCB Factory.
Build Author Cortellini Views 3164
The FEEDBACK FRACTAL Build
The Feedback Fractal Project (Project) - building "A Monument For Our Time." As its intent is to build a monumental sculpture, the Project will produce an object d'art. Yet, once begun, the Project has evolved a life and character of its own. I continue to follow the thread woven by the materials, the processes, and the people that come to it and in the end the work will not only be a faithful rendition of an image and a concept, it will also be a tapestry of the story of its making.
Build Author viktop Views 15622
Simple CNC Router (Nema17, V-slot 2040, Arduino, GRBL)
An OX-inspired mini desktop mill.
Build Author SecretSpy711 Views 19672
RigidOko
Heavily upgrading my 1200x500 Shapeoko 2... ...er, wait, scratch that... Building an all new machine, roughly the same size, that should be more rigid than a Shapeoko 3!
Build Author James Evanko Views 5425
Laser Displacement Golf Ball Scanner
Getting an accurate scan of a golf ball can be difficult with general-purpose 3D scanners. This purpose-built golf ball scanner uses a very accurate Keyence LK-081 laser displacement sensor with an Open Builds linear actuator for the vertical axis and a Sherline CNC rotary table for the turntable. Scan detail is determined by the sample step size and can be set arbitrarily based on desired scan time.
Build Author Todd Brous Views 4198
Modified Acro with build plate, Z-axis and OPT Laser
Modified Acro for laser engraving. Extra height and and a sturdy build surface for part fixtures, custom mount plates, OPT Laser, and a Z-Axis.
Build Author sausagePaws Views 1741408
DIY Embroidery Machine V2
My second attempt at an affordable sewing machine embroidery add on. This one uses readily available electronics modules and 3D printable parts where possible.
Build Author RV6APilot Views 3302
South Carolina Workbee 1000X1000
This is about my build of a Workbee 1000X1000 being built here in Trenton, SC. My goal is to use it to help cut the new panel for my RV6A airplane.
DIY CNC Machine
In this project, I show you how I built my DIY CNC machine. All moving parts of the DIY CNC router are running on ball bearings while the structural parts are made with natural materials, namely birch plywood and solid beech wood.
OpenBuilds ACRO Z Axis
Z-Axis for OpenBuilds ACRO system. It is sturdy enough to carry a small drill.
Build Author Stan Howe Views 2265
Bee the Boss
The frame of the CNC is going to to Bee a basic Work Bee with maybe 1 modification to the spoil board attachment. This will be located on a custom bench housing the electronics and vacuum. I plan to install Stepper online steppers, drivers, power supplies, and break out board. I will add a 1.5 KW water cooled spindle, with a radiator. The fans from the radiator will pull air from a filtered enclosure for all the electronics.
Build Author MarkM_NJ Views 18528
Spartacus Inspire
My very first openbuilds cnc machine. Followed along DaztheGas's Spartacus build.
Build Author Cortellini Views 4506
the Feedback Fractal project
The Story of the Scecina Memorial High School 1510 BUILD will unfold through a series of 10 minute Episodes. Each episode will consist of video showing how to assemble some aspect of the 1510 overlaid with a discussion about Technology, Art, Philosophy... and Life the Universe and Everything. Episode two is soon to follow. If sufficient interest ensues, the episodes may continue beyond the building of the 1510 to relate its use in the making of the Art.
Build Author pek Views 77019
Prusa i3 Bear Upgrade V2
Stronger frame for Prusa i3 MK2(s), MK2.5 and MK3 3D printer
Lead CNC build, Mansfield, Texas - BUILD COMPLETED WITH REVIEW OF THE KIT
The machine is a stock Lead CNC, with the Black Box controller and StepperOnline 269oz NEMA 23 motors. I'll be using the DeWalt 611 from Openbuilds, as well.
WorkLead, no wait, LeadBee, naw... WoodWorker
Improvements on the Lead machine using some Workbee parts
Build Author Christian James Views 7230
Workbee "style" 1010 cnc
This build is based on the Workbee 1010 CNC. It is not a kit build and is much the same as the original but with some significant changes made here and there as the build progresses.
Build Author TurfnSurf Views 5703
DIY C-Beam CNC
Theoretical Working Area: 360x360x75mm Actual Working Area: 300x300x75mm Will Update Later
Build Author Doug Rowley Views 3348
My Workbee 1010
This is a workbee 1010 build using the mechanical parts from Open Builds. The electrical and electronic parts were from a prior build of a Root 3 CNC by Sailor Pete.