Recent Activity
Activity stream for all registered members at OpenBuilds.
-
Giarc attached a file to the thread MGN linear rails.
Commonly available extruded aluminum angle worked for me. You can easily cut it with a chop saw to length and us a printed patter for...
Sep 24, 2023 at 7:20 PM
-
Giarc liked Rick 2.0's post in the thread Suggestions on building a waterproof gantry?.
Best suggestion would be to build it upside down to where the jet is shooting away from machine rather than into the middle of it. And...
Sep 24, 2023 at 6:37 PM -
David the swarfer replied to the thread Spindle running slowly help please.
but do note that the 24V stepper motor power supply that connects to the blackbox must also be on since it powers the 0-10v circuit.
Sep 24, 2023 at 2:57 PM -
David the swarfer liked Peter Van Der Walt's post in the thread Spindle running slowly help please.
Nothing special here. Just Min Freq not set correctly. See it often... Spindle max 24000rpm = 10v Spindle recommended min = 7200 rpm...
Sep 24, 2023 at 2:46 AM -
David the swarfer liked Peter Van Der Walt's post in the thread MKS DLC 32 problem..
You really have to go read the Grbl Wiki. MCS is explained in the FAQ page That alarm is explained in the Max Travel section of the...
Sep 24, 2023 at 2:43 AM -
Rick 2.0 replied to the thread Suggestions on building a waterproof gantry?.
Best suggestion would be to build it upside down to where the jet is shooting away from machine rather than into the middle of it. And...
Sep 23, 2023 at 6:49 PM -
Tom Dirriwachter replied to the thread Cube 3 / Pro hacks.
Nice work! I suspect it does a spin with the HostID and stores a bit in one of the two .bin files
Sep 22, 2023 at 8:02 PM -
Brian Slee attached a file to the thread Heavy Metal.
Almost ready to create the epoxy granite composite carriage rail. Casting mold is done, and I did a dry pack to get a good measure for...
Sep 22, 2023 at 3:17 PM
-
David the swarfer liked Peter Van Der Walt's post in the thread $33 missing.
Works just fine in testing... As it should and always has [ATTACH] The Servo firmware is still 1.1f, so you haven't flashed it...
Sep 22, 2023 at 6:18 AM
-
David the swarfer replied to the thread Changing the Probe routine.
CONTROL or Interface?
Sep 22, 2023 at 6:16 AM -
David the swarfer replied to the thread MKS DLC 32 problem..
and right here in the forum resources, stuff to read if you don't like videos. Home, Fusion360 and G53 Z moves How to 'Fake the home'
Sep 22, 2023 at 6:15 AM -
Rick 2.0 liked Honver's post in the thread spindle mounting for Openbuilds MiniMill kit.
I could not mount directly to the double wide C beam gantry plate because it would be too annoying to get to the back of the plate, and...
Sep 22, 2023 at 12:51 AM
-
Giarc liked Gary Caruso's post in the thread Breaking 1/8 inch endmill.
Another thing to watch out for is loose parts, need to use tabs (bridges or whatever we call them) to hold the loose parts from moving...
Sep 21, 2023 at 5:40 PM -
JustinTime replied to the thread OpenBuilds CONTROL Software.
As you've mentioned in the past, there are two kinds of E-Stop. One that shuts down everything, preventing just what you've said above,...
Sep 21, 2023 at 10:07 AM -
Brian Slee replied to the thread Heavy Metal.
I considered doing a second pass then I got a good look at my bit and thought it might be best not to push my luck. :nailbite:
Sep 21, 2023 at 9:36 AM