Build List
-
Active Filters:
be
Gerber 404 Retrofit
Not sure if the Blackbox X32 is the right option here, just looking for guidance.
C-beam Machine - Modesty
Modified C-beam Machine. Taller (30 cm) C-beam uprights in gantry, and longer 750 mm frame in Y direction. XL gantry plate on X (and Z?). Y will have additional 700 mm SBR16 rails as extra support and slightly raised bed to fit above stepper motor. Approx. machinable area of 370 x 370 mm.
Build Author EvanH Views 875
"Hawk" Heavy-duty dual-Z pseudo C-Beam
A compact, strong machine with very high Z clearance, yet can still mill aluminium easily.
Build Author Ryan Lock Views 122954
WorkBee CNC Machine
The WorkBee is our latest CNC Machine and is a culmination of all our experience, feedback, and suggestions from selling the OX CNC Machine over the past 2 years. The WorkBee is capable of accurately cutting foams, woods, plastics or aluminum at depths greater than 25mm to 0.2mm accuracy or greater.
Build Author Mark Carew Views 252300
C-Beam® Machine - Plate Maker
This C-beam Machine is an in affordable CNC plate maker and 3D carving machine!
KillerBee 1515 customized
Killerbee 1515 with modifications.
Build Author that-jim Views 41183
LINEAR RAIL SPHINX 55 (Blue OX plates)
Machine based on Sphinx 55 built with linear rails.
Build Author Cam Garrett Views 2171
Sturdy Motorized Photographic Copy Stand
i would like to build a sturdy motorized photographic copy stand. i have hobbled together a hand crank version using a used umbrella pole but it is not suitable as it is awkward and wobbly.
Dash X Direct, Cross-Beam 3d Printer
This is the next version of Dash, now operating much closer to its potential. Please message me if you need anything, such as Simplify3D settings, material information, design intent etc. Since the Pack-and-Go zip file is fairly large (120mB), here is a link where it can be downloaded: https://drive.google.com/file/d/1Q3ygyo_tTrB4UYIV62_wtCSCbWuE3krT/view?usp=sharing Note: I use Solidworks 2022, acquired through their Solidworks for Makers program (check it out!). A super deal at $100/yr
Y table for LEAD Lathe - essentially a High Z Cbeam XL
I built the lathe as a dedicated rotary axis, but I soon realized I could have a back up CNC for very little expense.
2 Axis Lathe cutter
Rubber company use as a lathe cutter for accurate cuts compared to hand cutting.
Build Author Rick 2.0 Views 14551
C-Beam Mini Mite
A small system with a big bite. Design achieves a good balance between machine size vs. build area, rigidity and ease of construction all while keeping build cost as low as possible.
Build Author Jason @ MCC Views 8988
QueenBee Pro CNC Router and Lathe
A 1000x1500mm QueenBee Pro with a 4th Axis Rotary attachment/Lathe Bed.
Travel Printer
Build using standard parts as much as possible, Open Builds etc. To keep printer usable for more materials will be trying a heated bed with rotary elec union for the thermistor and power.
M10CUBE PICO CNC. A Universal Controller
An attempt is to be a Unified Modular Controller based on M10CUBE platform. For GRBLHAL and MARLINHAL applications. HAL porting is under way 1 - WIZnet Pico Clone W5100S-EVB-Pico 2 v- 6 X StepStick. Not sure about the sixth driver, (Pico pins limitation) . External connectors for larger drivers 3 - Opto - isolated spindle PWM. 4 - HMI 5 - I/O on diferent modules and Ethernet 10MBPS communication. Patches will be written to GRBLHAL for Ethernet I/Os (Interrupted).
C-beam charmer
Double C-beam Y axis 500mm., Double 2080 X axis 600mm. , C-beam Z axis 250mm, TB-6600 drivers, MKS-DLC32v2 GRBL w/wi-fi and blue tooth
Build Author Shaun Weitzel Views 4670
OpenBuilds Lead 1515
First build of a Lead 1515!
New Workbee Z Axis
Hopefully an upgrade of the Z axis of the Workbee.
My C-Beam build and modifications
Modified C-Beam which I plan to add a laser module and eventually convert to C-Beam XL size.
Build Author Edgar Mata Views 19039
ME - Core XY 3d printer
I wanted to make my own Voron, so I made my own Voron,
Based on 608 tube Plasma Cutter
Simple steel tube design Plasma water table
Build Author Leonard Cross Views 33546
Workbee CNC Router/Laser/Plotter
A CNC machine with an expansive 30x30" work area, supporing a router, laser, simple plotting and work monitoring camera. Control includes a tethered control box, game controller style jog control, and relay controlled AC outlets for all appliances. Accessories include a 3D printed dust shoe, a complete spoilboard and hold down system, an XYZ touch probe and multiple vacuum retention boards to support full profile routing.
Build Author shanehooper Views 12234
SolidCore CoreXY 3D Printer
Modular and Scalable CoreXY Printer with all metal parts.
Build Author SOA Views 57683
GridBot Two: Powerfully Simple
Core XY, sensor-less homing, integrated camera, touch screen, pi, 32-bit controller, fast, quiet, beautiful prints. 300 x 300 x any build volume. Just change out the Z lead screws, rods, and four pillars. Total BOM around $700 USD. Build time around 6 hours.
Build Author Mark Carew Views 76528
OpenBuilds Workbee 1510 (60" x 40")
The OpenBuilds WorkBee 1510 - 1500x1000 Belt Driven CNC Machine
Build Author Steve Hall Views 2986
Cartesian Style Build UK
Another Cartesian style build with parts from the UK, US & China.
Build Author Scott Drake Views 14106
1500x1000 CNC Router
1500x1000, additional frame stiffening from laser cut Stainless steel bracing plates, Nema 34 motor upgrade and Hiwin 16mm ballscrew additions on the way. Ethernet Smooth stepper control, 2.2kw Water cooled spindle. Schneider atv320 variable speed drive. SICK inductive limit switches, Leadshine Em882S stepper drivers ,1kw 62V supply for Stepper drives
Some Improvements on the Workbee 1000x1000
Improvements both real and suggested for the Workbee assembly
Workbee with less irritations
My workbee build with some add ons
Build Author nickchnv Views 9944
Rigid Compact Desktop C-BEAM
This modified C-Beam, is a compact, powerful and affordable desktop CNC.
Custom push cart for CNC machines
I’m custom building a push table / cart for my cnc machines mostly out things I already had in my garage. Using a gray push utility cart as the main body and building around that.
Build Author CNCGear Views 8401
The BlackBee CNC
Ball screw drive, linear rail CNC Kit
Build Author Indieflow Views 109408
Indie i2
A lightweight, portable, accurate 3D Printer that has a good sized print area and small overall footprint that is easy to build, with easy to source components. The design is OpenSource allowing those with the capability to make their own parts get up and running.
Filament winder ( carbon fiber )
Carbon fiber filament winder
Build Author crypt-tek Views 8784
crypt-cube
The crypt-cube is another project I've been working on off and on over the past year, unlike my previous built C3DO this is a much smaller built with a volume of 318mm x 240mm x 220mm. With this build my main focus is precision and speed.
Build Author Kyo Views 22043
Sphinx 55
A Sphinx build to inspire and encourage all those who want to get started with cnc to check out Opensbuilds line of machine bundles and hardware.
Build Author Corey Corbin Views 4890
Ball Screw Carrier.
Create a ball screw carrier with out BF BK bearing blocks.
Build Author Frank Gore Views 7056
Kossel Extreme
A custom Delta printer for large projects with any filament that still retains speed and accuracy, all within a 15 amp/110VAC power budget. Based on Johann's Mini Kossel design.
Rotary axis for Workbee
Adding a rotary axis to the Workbee 1010. Including height modifications to the Workbee.
Another C-Beam machine
This is basically a Sphinx variant with few changes of my own...hope it'll work.
Retractable WorkBee1510 with Marlin+MarlinPanel high level build
WorkBee1510 with retractable space saving stand and customize build Marlin firmware and MarlinPanel (GCode Sender/UI)
Improved CBM
Yet another build of an improved C-Beam Machine, improving stiffness, size, versatility, and strength without increasing costs much.
Build Author Stokrotka74 Views 5546
Racoon CNC
This is a Sphinx variation, aimed to minimize footprint and maximize workarea. Work in progress.
YAWBM - Yet another Workbee Modification
Increase Z axis travel by 20-25mm with minimal modifications
Horizontal CNC V-Beem v1
V-Beem horizontal milling machine built on OpenBuilds components. Simple structure, great expansion possibilities, high stiffness.
Build Author Rob Taylor Views 15575
M4: 1510SS Heavy Mk.I
A 1500x1200mm, 20mm rail and 1610 ballscrew, heavy-duty, four-axis gantry machine. As high speed as spindle power MRR will allow for. Approx 4 x 3 x 1ft travels, intermediate size between benchtop and floor-scale units. Aiming at $10-15k machine in the $3k region.
Workbee with Duet controller
Workbee 1010 with Duet controller from Ooznest
Build Author Troy Joachim Views 15145
Prusa i3 Bear IDEX
Remix of the Prusa i3 Bear with added IDEX
Build Author Leboeuf Views 3622
Cartesian 3d printer
This is the build of a cartesian 3d printer made of an old Anet and Geeeteck, some 2020 alu profil and linear rail. Powered by a Rumba with a Nextion screen. It should be modular and accept dual Extrusion and laser engraving.
ApiNui - CNC Router ( an oversized workbee )
Based on the WorkBee CNC, this is an oversized router built with a specific use-case in mind, for manufacutring beehives, and beehive components
Workbee Z-axis Upgrade
Z-Axis upgrade with linear rails, SFU1204 Ball Screw and full aluminium construction.
Build Author OpenBuilds Views 5346
V-Slot Ventilator
The idea is to make a simple effective ventilator, studying the concept of using a simple push process with and actuator.
1515 Deluxe
Build features include a double c-beam gantry (bonded & mechanically fastened), linear x rails, custom gantry end plates, a custom linear rail & ballscrew Z axis, and custom lead screw tensioning plates. The primary goal was to remove twist from the 1500mm gantry & stiffen the Z axis.
WorkBee Saving Lives
Using the WorkBee to protect doctors against Corona virus.
Build Author Joe F Views 6826
Rack and Pinion Cartesian Mill
This is a rework of a previous build I did on here, a mostly printed cartesian CNC. Initially intended to just be an update to that, but so many things changed including the linear motion and every single part has been modified significantly that I felt as though it deserved a whole new build.
Build Author Neil Rosenberg Views 35105
Dash-X 3D Printer: Innovative design
Cross-beam Cartesian 3d printer with dual master/slave lightweight fiberglass drive shafts, BMG style extruder with Bowden (Capricorn) tubing. Hot end is Creality Ender 3 style with two fans and BLTouch for autoleveling. Filament runout sensor is also included.
Build Author SandeepsCNC Views 10497
Raspberry Pi CNC Software
The main objective is to build a software which can completely run on a single board computer, Rasbperry Pi, to reduce the complete cost of building a cnc machine. The software is extensively tested and can be run on any raspberry pi 2/3 boards. With no G-Code dependency, you can do complex 3D relief carving to simple tasks with simple GUI based project development environment. Please go through the YouTube channel for more details https://youtu.be/8KOXqLpvscg
Model train lift - scale HO
This build is about a model train lift in a secure and dust free storage. It is a roll on/roll off concept for a model train layout.
Build Author jeff johnson Views 4656
workbee 1510
Getting more height out of the !510
Build Author txcomp Views 5590
WorkBee 1010 "Get Rid of the Slop" Build
My goals for this build were to eliminate slop and flex while also allowing easy serviceability.
Build Author Kenneth Witthuhn Views 7268
Openbuilds CNC (witthuhnCNC XKLBR-1S)
Based on the popular C-beam / V-wheel design, with the largest available work area, relative to machine size. Screw driven with anti-backlash, integrated drag chains, Carbon fibre gantry plates, Openbuilds BlackBox Controller (USB), Transformer & kill switches, with internal wiring, limit switches & Nema 23 motors.
Build Author Mark Carew Views 6495
OpenBuilds PowerCase
A simple to assemble, super clean and safe PSU case solution that fits into the OpenBuilds wire management ecosystem
My C-Beam machine...from 500 to 1000mm base
C-Beam machine - 1000mm base.
C-Beam Dust Shoe
A short description of the dust shoe I made for my machine.
My Ooznest Workbee V2.0 build
I'm new to this whole process, so this is a build by a newbie for newbies.
My C-Beam machine...
A C-Beam machine design, strengthened with extra brackets and plates. GRBL controlled, opto-isolated inputs, jogging box.
Workbee 1010
Hey all looking forward to sharing this build, I’ve learned a lot reviewing many of these great builds.
Build Author Kims3DIY Views 16645
Beamlazer Laser cutter CO2 100W
Hi everyone, im new to the world of lasercutters but i have been granted access for a Trotec laser for a while with old firmware and only compability trought Windows XP. Then i decided to build my own laser, with some easier workflow and support for Windows 10. Since im still a student i have limited resources, so i will try too use scrap parts as much as possible. I will publish photos and updates during my build continously. Gladly taking advices from others.
Build Author Darren Dickson Views 3015
3D printed CNC Machine
So I thought I would make the Leon van den Beukel version three 3D printed CNC Machine, it is the third incarnation so you would expect a relatively bug-free CNC Machine with a strong foundation.
Build Author Mark Carew Views 139972
OpenBuilds MiniMill
This OpenBuilds Mini Mill is a great go-to desktop sized CNC milling plate / part maker and 3D carving machine!
Build Author Mark Carew Views 47019
OpenBuilds Sphinx 55 (20" x 20")
The OpenBuilds Sphinx 55 - 500x500 Lead Screw Machine
Build Author Mark Carew Views 28768
OpenBuilds Sphinx 1050 (20" x 40")
The OpenBuilds Sphinx 1050 - 500x1000 Lead Screw Machine
Build Author Vunnie Views 5660
Workbee CNC on steroids
My First major improvement was changing the controller to a Acorn board. I loved the way a dedicated userinterface was speeding up my workflow. Next project my Y Axis. On Aliexpress I ordered a couple of 16mm ballscrews and some lineair rail. Before I took my gantry off I quickly made some aluminium profiles to fit my carriages. Withouth any doubt these improvements where worth it
Rise of the Sphoenix
I am building a Sphinx 55 from the bones of my old C-Beam machine. Rising from the ashes so to speak.
Gary's Mod Plates for OX Heavy Duty X and Z
Gary's take on the OX HD X and Z plates, making it stiffer, adding mini wheels to the C-beam and Quick removable Z axis.
Build Author Mark Carew Views 14185
Nema 23 Belt and Pinion Actuator
This easy to build and effective system can take your builds to the next level! This design is strong and accurate and could be the solution/upgrade that you've been looking for!
Build Author Mark Carew Views 18728
V-Slot™ Nema 23 Linear Actuator (Belt Driven)
This example build shows how easy it is to make a linear actuator using a few OpenBuilds Parts.
Build Author Mark Carew Views 19418
C-Beam® XLarge Linear Actuator
This OpenBuilds C-Beam XL actuator is the backbone of a lot of the awesome builds put together by the OpenBuilds community
Build Author Mark Carew Views 13244
C-Beam XLarge X/Y Table
This OpenBuilds C-Beam XLarge X/Y Table is a great display of how easy it is to modify and create awesome configurations with the OpenBuilds system!
Build Author Mark Carew Views 12353
NEMA 17 Belt and Pinion Actuator
This Belt and Pinion actuator is a great example of how easy it is to convert your machine into a belt drive system.
Build Author Mark Carew Views 10328
C-Beam® Double Wide Gantry Actuator
This easy to build actuator is configured to have not only strength, but accuracy! This low profile option offers endless possibilities, and we cant wait to see how this actuator is implemented in your build ideas!
Build Author Mark Carew Views 116949
C-Beam™ Linear Actuator
Here are a few helpful C-Beam actuator ideas that will help you get a start on your builds
Build Author tmadrms Views 5950
C-Beam Mods
C-beam machine mods.
Build Author Mark Carew Views 24224
OpenBuilds Workbee 1050 (40" x 20")
The OpenBuilds WorkBee 1050 - 1000x500 Lead Screw Driven CNC Machine
Build Author Mark Carew Views 68223
OpenBuilds Workbee 1010 (40" x 40")
The OpenBuilds WorkBee 1010 - 1000x1000 Lead Screw Driven CNC Machine
"Stung by the Bee" OB Workbee 1010 Build
This will be a build Log for my Open Builds Workbee 1010 Build. I will keep a full descriptive log of the build and make any notes in the hope that it will help other builders that decide they would like to build this machine.
TITANXY (Fixed Build Plate, Quad Z Screw, CoreXY)
Super Rigid CoreXY 3D Printer
Build Author taratata2016 Views 6755
Panther 3D printer
After use of the i3 Prusa 200x200x180, the volume increases to 300x300x450 on the V-Slot and driven by a Megatronics V3
Build Author SecretSpy711 Views 19669
RigidOko
Heavily upgrading my 1200x500 Shapeoko 2... ...er, wait, scratch that... Building an all new machine, roughly the same size, that should be more rigid than a Shapeoko 3!
A More Rigid C-Beam
I added the steel to create a less flexible milling surface to make heavier cuts in aluminum. I can also do light steel cutting now as well. I wish OpenBuilds made a steel and rail version of these kits.
Workbee 1015 (50" wide by 30")
A Workbee able to cut 48"x24" material, built to continuously feed material so one can cut full sheets of ply.
CBeam Sphinx Upgrade
Simple upgrade of the Y axis on a Cbeam sphinx from 500mm to 1000mm.
Build Author KronBjorn Views 3541
WorkBee Lead 1010, Reduced Footprint, Nema17
This is a WorkBee 1000x1000mm with lead screws and Nema17's. It has a reduced footprint, with the geared Nema's inside the frame.
Build Author RV6APilot Views 3302
South Carolina Workbee 1000X1000
This is about my build of a Workbee 1000X1000 being built here in Trenton, SC. My goal is to use it to help cut the new panel for my RV6A airplane.
Build Author Stan Howe Views 2265
Bee the Boss
The frame of the CNC is going to to Bee a basic Work Bee with maybe 1 modification to the spoil board attachment. This will be located on a custom bench housing the electronics and vacuum. I plan to install Stepper online steppers, drivers, power supplies, and break out board. I will add a 1.5 KW water cooled spindle, with a radiator. The fans from the radiator will pull air from a filtered enclosure for all the electronics.
My giant "WORKBEE" 1750mm X 1750mm by ooznest
CNC MACHINE WORKBEE'S table making
Build Author MarkM_NJ Views 18525
Spartacus Inspire
My very first openbuilds cnc machine. Followed along DaztheGas's Spartacus build.
My Workbee build
Workbee, 1000mmX750mm , from China
Build Author pek Views 77011
Prusa i3 Bear Upgrade V2
Stronger frame for Prusa i3 MK2(s), MK2.5 and MK3 3D printer
Build Author Ariel Yahni Views 5184
OB 2x72 Belt Grinder
Build a 2x72 Belt Grinder out of OpenBuilds V-Slots