Build List
cnc vreesbank 2500x30000
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
This cnc milling machine is 3 meters by 30 meters,
![Fixed Gantry CNC Router with Old Industrial Supplies](https://openbuilds.com/data/article_images/l/6/6536.jpg?t=1546123345)
Build Author
MattR
Views
14967
Fixed Gantry CNC Router with Old Industrial Supplies
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
I got lucky enough to purchase aluminum extrusions and linear motion components (and nuts/bolts/etc) at scrap metal prices when a bunch of industrial automation equipment was decommissioned. The only problem is that the aluminum extrusions are not metric sizes... they are the 1.5"x3" 80/20 series. It has presented a few challenges but nothing too bad.
TrueUp Kit Version
![](https://openbuilds.com/data/article_cat_images/s/0/272.jpg?t=0)
A Cartesian printer using bushings for the Z axis instead of wheels or linear bearings. The design also synchronizes two Z axis screws with a timing belt for a level lift. The ratio of the drive pulley and Z axis pulleys produce .005 lift per full step on a 200 step motor, eliminating layer resolution "drift" caused by microstepping.
![Hyatt and My Journey to Tonehenge](https://openbuilds.com/data/article_images/l/7/7945.jpg?t=1543606004)
Build Author
Craig Hollabaugh
Views
3678
Hyatt and My Journey to Tonehenge
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
I'm conducing guitar loudspeaker cabinet fabrication technique research (material type/thickness, mechanical joints, adhesives, etc) and how these relate to cabinet/speaker coupling and enclosure resonance with respect to psycho-acoustics. Basically, does one speaker cab sound better than another and why?
"Stung by the Bee" OB Workbee 1010 Build
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
This will be a build Log for my Open Builds Workbee 1010 Build. I will keep a full descriptive log of the build and make any notes in the hope that it will help other builders that decide they would like to build this machine.
![Miter Saw Stop Block](https://openbuilds.com/data/article_images/l/6/6506.jpg?t=1518645861)
Build Author
rkugler
Views
5415
Miter Saw Stop Block
![](https://openbuilds.com/data/article_cat_images/s/0/295.jpg?t=0)
Just starting a miter saw stop system. Any suggestions appreciated.
x_y_module laser engraver
![](https://openbuilds.com/data/article_cat_images/s/0/303.jpg?t=0)
low cost 2 axis cnc laser, really portable and easily expandable
![Modified LEAD machine](https://openbuilds.com/data/article_images/l/8/8805.jpg?t=1568735843)
Build Author
mjenkins5720
Views
1996
Modified LEAD machine
![](https://openbuilds.com/data/article_cat_images/s/0/295.jpg?t=1389472559)
At the moment this build is in progress, I will be updating the files as I finish the remainder of the machine. This machine is intended to be a multipurpose CNC, but a bit bigger than a desktop unit. The machine is scalable in the X and Y axis.
Cnc od grinder and thread grinder
![](https://openbuilds.com/data/article_cat_images/s/0/295.jpg?t=0)
This is a totally original build of an od id grinder and thread grinder, I hope.
BKE Lead 1010 - First CNC Router
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=1389472260)
LEAD CNC
![CNC Cyclone PCB Factory, my way, step by step.](https://openbuilds.com/data/article_images/l/7/7442.jpg?t=1533286334)
Build Author
reef
Views
10440
CNC Cyclone PCB Factory, my way, step by step.
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
I'd like to renew my cnc for PCB so I decide to create new one from an existing project named Cyclone PCB Factory.
![CoreXY 3D build one](https://openbuilds.com/data/article_images/l/4/4874.jpg?t=1569010665)
Build Author
recoush
Views
7575
CoreXY 3D build one
![](https://openbuilds.com/data/article_cat_images/s/0/272.jpg?t=1389472082)
an 8020 build with 1010 extrusion (1") Square tubing Rough size is 24x24x36 (600x600x900) The expected usable print area 21.5x21.5X32"roughly (510x510x760) An XY 3D printer with 3 extruders and 3 Z-axis 0.9 degree motors the table (Z-AXIS) will lift up to the XY Carriage on 3 12mm linear rod and 3 8mm Lead screw's Corexy designs complete and Z-axis build is started don’t have a 3D cad system yet so building my prototypes on a pcb layout tool
Cnc Mill using standard and 3d printed cimponents
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
I used the cad designs for the c beam to find a solution to my initial sourcing problem. I figured that I could use 2x 20x20 and 1x 20x80 Profil to create a c beam actuator. I sourced all of the profiles from a local machin builder and t-nuts and screws in my local hardware store. Some parts are currently in 3d printed pla for testing reasons.
![The FEEDBACK FRACTAL Build](https://openbuilds.com/data/article_images/l/8/8518.jpg?t=1557431974)
Build Author
Cortellini
Views
3273
The FEEDBACK FRACTAL Build
![](https://openbuilds.com/data/article_cat_images/s/0/295.jpg?t=0)
The Feedback Fractal Project (Project) - building "A Monument For Our Time." As its intent is to build a monumental sculpture, the Project will produce an object d'art. Yet, once begun, the Project has evolved a life and character of its own. I continue to follow the thread woven by the materials, the processes, and the people that come to it and in the end the work will not only be a faithful rendition of an image and a concept, it will also be a tapestry of the story of its making.
![Panther 3D printer](https://openbuilds.com/data/article_images/l/4/4577.jpg?t=1568965395)
Build Author
taratata2016
Views
6915
Panther 3D printer
![](https://openbuilds.com/data/article_cat_images/s/0/272.jpg?t=0)
After use of the i3 Prusa 200x200x180, the volume increases to 300x300x450 on the V-Slot and driven by a Megatronics V3
![D&R Tiger Paw build combo](https://openbuilds.com/data/article_images/l/6/6856.jpg?t=1550455582)
Build Author
Lasersc
Views
9460
D&R Tiger Paw build combo
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
The Tiger Paw will be a 1000mm X 500mm Cartesian style CNC with the Minimill attached to the end. It is named the D&R Tiger Paw because my son, Daniel, and myself, Richard, will put this Tiger strong and fast machine together. Our goal is to have a Tiger strong build with a Paw print that wouldn’t take up a huge amount of space in our garage.
CNC 1000x1000mm C-beam
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
inspired by http://openbuilds.org/builds/c-beam-sphinx.3605/
Reworked Routkit SD
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
I could not "tram" the spindle to the table. I found that the V Rails could not accurately be adjusted so the Gantry was equal distance from the spoilboard in multiple places.
![Simple CNC Router (Nema17, V-slot 2040, Arduino, GRBL)](https://openbuilds.com/data/article_images/l/8/8485.jpg?t=1567627790)
Build Author
viktop
Views
15956
Simple CNC Router (Nema17, V-slot 2040, Arduino, GRBL)
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
An OX-inspired mini desktop mill.
Mammoth (Delta printer)
![](https://openbuilds.com/data/article_cat_images/s/0/272.jpg?t=0)
Massive Delta printer with a print area of 25 Inches (634mm).
![CNC Auto-pipette](https://openbuilds.com/data/article_images/l/8/8784.jpg?t=1567236148)
Build Author
Sir Bagels
Views
2117
CNC Auto-pipette
![](https://openbuilds.com/data/article_cat_images/s/0/295.jpg?t=0)
Senior Design Project Bennett Robertson, Megan England University of Iowa College of Engineering
H-Bot CoreXY Cube
![](https://openbuilds.com/data/article_cat_images/s/0/272.jpg?t=0)
Dead build.
![The D & R TigerPaw Trilogy](https://openbuilds.com/data/article_images/l/8/8729.jpg?t=1564161580)
Build Author
Lasersc
Views
3820
The D & R TigerPaw Trilogy
![](https://openbuilds.com/data/article_cat_images/s/0/303.jpg?t=0)
Hopefully this will be a quick guide to one way that you can add a laser to an existing CNC router.
![Vulcan Bot](https://openbuilds.com/data/article_images/l/8/8775.jpg?t=1566757514)
Build Author
Keith Davis
Views
3071
Vulcan Bot
![](https://openbuilds.com/data/article_cat_images/s/0/272.jpg?t=0)
A 200mm x 300mm x 200mm workhorse that never needs leveling due to Posi-Drive Leveling design.
Minimalist Laser Platform
![](https://openbuilds.com/data/article_cat_images/s/0/303.jpg?t=0)
Minimalist laser platform built with Makerlink connectors and modified Nema 17 stepper mounts used as gantry plates.
CNC Router Machine
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
CNC Router with working area 550*550*200
![Laser Displacement Golf Ball Scanner](https://openbuilds.com/data/article_images/l/8/8728.jpg?t=1564151634)
Build Author
James Evanko
Views
5661
Laser Displacement Golf Ball Scanner
![](https://openbuilds.com/data/article_cat_images/s/0/298.jpg?t=0)
Getting an accurate scan of a golf ball can be difficult with general-purpose 3D scanners. This purpose-built golf ball scanner uses a very accurate Keyence LK-081 laser displacement sensor with an Open Builds linear actuator for the vertical axis and a Sherline CNC rotary table for the turntable. Scan detail is determined by the sample step size and can be set arbitrarily based on desired scan time.
Openbuilds C-beam
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=1389472260)
This is a build supported by Ooznest by a team of girls in Year 8 (12/13 years old) to machine model F1 cars for the F1 in Schools competition.
C_Beam X5L Hybrid_Tank
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
classic router with a ab table
![Prusa i3 Bear Upgrade V2](https://openbuilds.com/data/article_images/l/6/6428.jpg?t=1519671067)
Build Author
pek
Views
77620
Prusa i3 Bear Upgrade V2
![](https://openbuilds.com/data/article_cat_images/s/0/272.jpg?t=0)
Stronger frame for Prusa i3 MK2(s), MK2.5 and MK3 3D printer
![Rawcnc 1.5 Desktop Edition](https://openbuilds.com/data/article_images/l/5/5771.jpg?t=1529849503)
Build Author
roadss
Views
23105
Rawcnc 1.5 Desktop Edition
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
This will showcase the build of my Rawcnc 1.5. A rigid cnc router from the Swedish company Rawcnc, featuring a rather cool linear motion system, rack & pinion and steel reinforced X-axis capable of milling aluminum.
75x75
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
Simple cnc with 5mm steel plates.
OX (Large) CNC
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
Building a Large OX CNC Open Build on a fold down table.
Workbee 1015 (50" wide by 30")
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
A Workbee able to cut 48"x24" material, built to continuously feed material so one can cut full sheets of ply.
![Workbee 1510 Screw Driven](https://openbuilds.com/data/article_images/l/8/8265.jpg?t=1549819113)
Build Author
msdosfx
Views
5135
Workbee 1510 Screw Driven
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
Workbee 1510 screw driven build by MsDosFX.
Openbuilds Co2 80w Laser Cutter
![](https://openbuilds.com/data/article_cat_images/s/0/303.jpg?t=0)
Co2 80 watt openbuilds laser cutter, 1200mm laser tube, 1500x1000x500mm dimensions. Build frame first and then panels to be added.
CBeam Sphinx Upgrade
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
Simple upgrade of the Y axis on a Cbeam sphinx from 500mm to 1000mm.
![CoreCube3D - A CoreXY 3D Printer](https://openbuilds.com/data/article_images/l/8/8109.jpg?t=1546581339)
Build Author
CoreCube3D
Views
18833
CoreCube3D - A CoreXY 3D Printer
![](https://openbuilds.com/data/article_cat_images/s/0/272.jpg?t=0)
Building a CoreXY based 3D printer using primarily parts from China on eBay. Large 500mm frame.
![V-Slot Modular Sit/Stand Desk](https://openbuilds.com/data/article_images/l/1/1615.jpg?t=1421190050)
Build Author
Mark Carew
Views
17468
V-Slot Modular Sit/Stand Desk
![](https://openbuilds.com/data/article_cat_images/s/0/295.jpg?t=0)
In this build we put together an awesome modular stand-up or sit down desk that is perfect of any home or office.
EOX v2
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
Upgrading my CNC router to run on ball screws. Me and the belts where not getting along.
KeePrint Monster
![](https://openbuilds.com/data/article_cat_images/s/0/272.jpg?t=1389472082)
Large 2 foot x 3 foot x 4.5 foot build volume Core XY printer build in process at this point. I am designing everything from scratch and using typincal parts bought from amazon for the build.
Mushu - Large Scale CoreXY
![](https://openbuilds.com/data/article_cat_images/s/0/272.jpg?t=0)
20x26x28 inch Build Volume CoreXY. Unlike many builds, I've decoupled the XY movements from the Z-Axis lead screws to help prevent Wobble, will be using linear guide rails, and mains powered bed heater, and a bed that is Allowed to thermally grow. This build is JUST narrow enough to fit through a standard sized doorway.
Large format laser
![](https://openbuilds.com/data/article_cat_images/s/0/303.jpg?t=0)
Large format laser build for Student use at my school as well as some personal use.
![WorkBee Lead 1010, Reduced Footprint, Nema17](https://openbuilds.com/data/article_images/l/8/8650.jpg?t=1560690979)
Build Author
KronBjorn
Views
3649
WorkBee Lead 1010, Reduced Footprint, Nema17
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
This is a WorkBee 1000x1000mm with lead screws and Nema17's. It has a reduced footprint, with the geared Nema's inside the frame.
Vacuum laser table
![](https://openbuilds.com/data/article_cat_images/s/0/303.jpg?t=0)
Large 10’x6’ vacuum table made from steel tubing and 1/4 inch steel plate
![Modified Acro with build plate, Z-axis and OPT Laser](https://openbuilds.com/data/article_images/l/7/7331.jpg?t=1560557385)
Build Author
Todd Brous
Views
4337
Modified Acro with build plate, Z-axis and OPT Laser
![](https://openbuilds.com/data/article_cat_images_nondefault/s/0/303.jpg?t=1451692706)
Modified Acro for laser engraving. Extra height and and a sturdy build surface for part fixtures, custom mount plates, OPT Laser, and a Z-Axis.
C Beam Rotary
![](https://openbuilds.com/data/article_cat_images/s/0/297.jpg?t=1389472486)
I've used the good work of Openbuilds & expanded it to suit.
![Lithgow Mens Shed CNC build](https://openbuilds.com/data/article_images/l/7/7875.jpg?t=1542793638)
Build Author
RobFromLDMS
Views
4076
Lithgow Mens Shed CNC build
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
The tale of how we put together our CNC Router, and some of the difficulties encountered. It is now ready for final testing and commissioning.
Rotary CNC
![](https://openbuilds.com/data/article_cat_images/s/0/297.jpg?t=1376658449)
I'm building a machine specifically for doing 4th axis work on woodwind instruments.
![South Carolina Workbee 1000X1000](https://openbuilds.com/data/article_images/l/8/8531.jpg?t=1557780245)
Build Author
RV6APilot
Views
3409
South Carolina Workbee 1000X1000
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
This is about my build of a Workbee 1000X1000 being built here in Trenton, SC. My goal is to use it to help cut the new panel for my RV6A airplane.
![Bee the Boss](https://openbuilds.com/data/article_images/l/8/8334.jpg?t=1558487150)
Build Author
Stan Howe
Views
2398
Bee the Boss
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
The frame of the CNC is going to to Bee a basic Work Bee with maybe 1 modification to the spoil board attachment. This will be located on a custom bench housing the electronics and vacuum. I plan to install Stepper online steppers, drivers, power supplies, and break out board. I will add a 1.5 KW water cooled spindle, with a radiator. The fans from the radiator will pull air from a filtered enclosure for all the electronics.
ricks workbee build
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=1389472260)
i had the ox build and wanted to do a more beeffer style so i went with a workbee style machine ..
![PrintAir CoreXY](https://openbuilds.com/data/article_images/l/2/2718.jpg?t=1443856231)
Build Author
Keith Davis
Views
18030
PrintAir CoreXY
![](https://openbuilds.com/data/article_cat_images/s/0/272.jpg?t=1389472082)
A CoreXY/Bowden design with a belt driven Z axis. This is a box design without the front end of the box, making the print area and maintenance, like changing a nozzle, easily accessible.
Phlux Core XY Laser Etcher
![](https://openbuilds.com/data/article_cat_images/s/0/303.jpg?t=0)
A 750mm x 1000mm Core XY Laser Etcher/Cutter. To cut down on cost I tried to have as many parts as possible be printed.
![CNC FOR EVERYONE!](https://openbuilds.com/data/article_images/l/0/596.jpg?t=1399598080)
Build Author
John J Talavera
Views
17381
CNC FOR EVERYONE!
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
This build was very complex due to the fact I wanted to create a low cost larger than normal CNC. I did not want a MDF or plastic body. I wanted it to be able to do more than most CNC routers this size on the market.
Taller couch legs
![](https://openbuilds.com/data/article_cat_images/s/0/295.jpg?t=0)
A simple but elegent couch legs
Black out Edition Workbee 1010
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
Thanks to all the Open Build elves that meticulously package and wrap all the little tiny parts and pieces. I have put in a request to get you people a raise..
Cnc mill, Plasma cutting and weld table
![](https://openbuilds.com/data/article_cat_images/s/0/295.jpg?t=0)
A functional table for plasma cutting, welding, tooling........
![PhlatPrinter MK 3](https://openbuilds.com/data/article_images/l/5/5207.jpg?t=1497557010)
Build Author
Mark Carew
Views
32552
PhlatPrinter MK 3
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
The Phlatprinter 3 was designed to be used in a small shop with the ability to cut large sheets of foam for RC airplane projects. The idea was that you could save all of your aircraft as models and tweak to perfection after every flight.
![Original PhlatPrinter](https://openbuilds.com/data/article_images/l/0/95.jpg?t=1389473544)
Build Author
Mark Carew
Views
71196
Original PhlatPrinter
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
Phlatprinter foam cutting CNC machines are awesome space saving mills that use a rotary axis as a sheet feed.
![Spartacus Inspire](https://openbuilds.com/data/article_images/l/6/6670.jpg?t=1519708480)
Build Author
MarkM_NJ
Views
18665
Spartacus Inspire
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
My very first openbuilds cnc machine. Followed along DaztheGas's Spartacus build.
DTG OX
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
From where Mark left off from the Ox build I am going to film the whole process of customizing the Ox.
GhettoPrinter
![](https://openbuilds.com/data/article_cat_images/s/0/272.jpg?t=0)
Dirt cheap build.
![the Feedback Fractal project](https://openbuilds.com/data/article_images/l/8/8139.jpg?t=1546966147)
Build Author
Cortellini
Views
4628
the Feedback Fractal project
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
The Story of the Scecina Memorial High School 1510 BUILD will unfold through a series of 10 minute Episodes. Each episode will consist of video showing how to assemble some aspect of the 1510 overlaid with a discussion about Technology, Art, Philosophy... and Life the Universe and Everything. Episode two is soon to follow. If sufficient interest ensues, the episodes may continue beyond the building of the 1510 to relate its use in the making of the Art.
Open source large format CNC-machine and 3D printer
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
For a schoolproject we decided to build this large format CNC-machine. The greatest part of the mechanics were sourced from OpenBuilds.
![SLA (Resin) 3D Printer](https://openbuilds.com/data/article_images/l/5/5069.jpg?t=1497077723)
Build Author
mytechno3d
Views
23657
SLA (Resin) 3D Printer
![](https://openbuilds.com/data/article_cat_images/s/0/272.jpg?t=0)
SLA LCD 3D Printer ( 8.9'' LCD screen )
CNC Hot Wire Cutter 4 Axis for Cutting Foam Wings
![](https://openbuilds.com/data/article_cat_images/s/0/295.jpg?t=0)
My build is to allow me to cut foam wings using CNC Hot Wire Cutter.
Shapeoko 2 - my first CNC
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
This was my first foray into CNC. I chose to go with a reliable kit build since my knowledge of GCode, controllers, and steppers was pretty rudimentary.
Hevavy duty 1300mm x 1300mm laser cutter Ceramic tube Servo motors
![](https://openbuilds.com/data/article_cat_images/s/0/303.jpg?t=0)
Starting the next Laser build, Plan to complete within 60 days.
![MPG Jog Controller for CNC xPRO](https://openbuilds.com/data/article_images/l/8/8235.jpg?t=1549135510)
Build Author
Spark Concepts
Views
4386
MPG Jog Controller for CNC xPRO
![](https://openbuilds.com/data/article_cat_images/s/0/295.jpg?t=0)
Been playing around with an MPG Jogwheel
![Rostock TETRA V0](https://openbuilds.com/data/article_images/l/4/4091.jpg?t=1478477284)
Build Author
crystaldragon141
Views
5605
Rostock TETRA V0
![](https://openbuilds.com/data/article_cat_images/s/0/272.jpg?t=0)
This is an experiment to build a Linear Delta Printer using four towers instead of three. Primary reasons: 1. Build area is roughly cubic vs roughly cylindrical 2. Greater speed and precision from additional control provided by fourth tower. 3. Symmetric kinematics from even number of towers.
iTopie RepRap - 3D Printer
![](https://openbuilds.com/data/article_cat_images/s/0/272.jpg?t=0)
A stable and strong 3D printer made of 16mm MDF and machined on my OX.
SMD Pick and place machine - Smoothieboard/OpenPnp
![](https://openbuilds.com/data/article_cat_images/s/0/295.jpg?t=0)
A dual head PNP machine that uses Openbuilds hardware, a Smoothieboard controller, dual camera vision, automatic/drag feeders, and OpenPnp.
![OB 2x72 Belt Grinder](https://openbuilds.com/data/article_images/l/8/8421.jpg?t=1554164244)
Build Author
Ariel Yahni
Views
5361
OB 2x72 Belt Grinder
![](https://openbuilds.com/data/article_cat_images/s/0/295.jpg?t=0)
Build a 2x72 Belt Grinder out of OpenBuilds V-Slots
Large format plasma ox
![](https://openbuilds.com/data/article_cat_images/s/0/303.jpg?t=0)
I will update this as I go, cad files upon request. My x beam is basically a belt driven r7
Kraken Core-XY Printer
![](https://openbuilds.com/data/article_cat_images/s/0/272.jpg?t=0)
Core-XY build witha quad nozzle
![Coined by my family as the: Davomatic](https://openbuilds.com/data/article_images/l/7/7484.jpg?t=1534077885)
Build Author
JerwanDavis
Views
4941
Coined by my family as the: Davomatic
![](https://openbuilds.com/data/article_cat_images/s/0/272.jpg?t=0)
Build Notes: Here are all the parts necessary to re-produce this design. Please note, all of the parts are either sourced through openbuilds or have been selected and printed from thingiverse.
![The Forever Project](https://openbuilds.com/data/article_images/l/7/7977.jpg?t=1543788838)
Build Author
Bikes and Beer
Views
3818
The Forever Project
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
Workbee 1010 Lead Screw with water cooled spindle and enclosure
MiniMill build
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
A table top OpenBuilds MiniMill build. 48V 52mm spindle with ER11 collets.
Lead CNC build, Mansfield, Texas - BUILD COMPLETED WITH REVIEW OF THE KIT
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
The machine is a stock Lead CNC, with the Black Box controller and StepperOnline 269oz NEMA 23 motors. I'll be using the DeWalt 611 from Openbuilds, as well.
Indoor Drumline Props
![](https://openbuilds.com/data/article_cat_images/s/0/295.jpg?t=0)
Triangular Towers
![Delta250](https://openbuilds.com/data/article_images/l/7/7930.jpg?t=1543525836)
Build Author
thinman
Views
7315
Delta250
![](https://openbuilds.com/data/article_cat_images/s/0/272.jpg?t=0)
A 250x250 mm Delta Printer utilizing a Duet Wifi controller and a Titan Aero direct drive extruder.
LimpyCNC
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
Inpired by the OpenBuilds OX and PrintrBot Crawlbot. This is the LimpyCNC. It's still a work-in-progress. But it provides a 120x120cm work space without using up 150x150cm of garage space.
![Clear Acrylic Dust Shoe](https://openbuilds.com/data/article_images/l/8/8392.jpg?t=1552523209)
Build Author
Cosmosteel
Views
3686
Clear Acrylic Dust Shoe
![](https://openbuilds.com/data/article_cat_images/s/0/295.jpg?t=0)
Attaches router with screw clamping. Clear Skirt is 2" long or can be made longer if requested. Works well keeping dust within the chamber. It can be made to fit shapeoko, ox cnc, workbee, xcarve, 6040, laguna,piranha, millright etc. with similar setup including Bosh, Makita , dewalt 611 routers or spindles.
![Vox Solid State](https://openbuilds.com/data/article_images/l/6/6030.jpg?t=1513689971)
Build Author
CharlieShimota
Views
14378
Vox Solid State
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
I never thought owning a CNC machine was possible until I stumbled upon the Openbuilds site. After viewing numerous builds I was drawn to the Ox by Mark Carew but ultimately decided on a build of similar design, Halloumi by Savvas. It's a C-beam design driven by Nema 23 steppers with Acme lead screws. Like Savvas I will be fabricating temporary plates to get up and running then use the machine to mill the final plates. The material I'm using for the temp plates is solid surface (Avonite).
![My custom world of tanks gaming desk built by Ragged Edge Eaming Solutions](https://openbuilds.com/data/article_images/l/8/8395.jpg?t=1552670721)
Build Author
Hidro669
Views
2680
My custom world of tanks gaming desk built by Ragged Edge Eaming Solutions
![](https://openbuilds.com/data/article_cat_images/s/0/295.jpg?t=0)
summary huh... If it doesnt fit MAKE IT!
C-Beam Machine Build
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=1389472260)
This is my first CNC router build. I want to gain basic CNC building experience so I can go on to build other items such as a frosting or pancake printer.
Butterfly 3DP V 1.0
![](https://openbuilds.com/data/article_cat_images/s/0/272.jpg?t=0)
tronxy x3 like
![OpenCase Mounting Kit](https://openbuilds.com/data/article_images/l/7/7820.jpg?t=1542035748)
Build Author
Mark Carew
Views
5114
OpenCase Mounting Kit
![](https://openbuilds.com/data/article_cat_images/s/0/295.jpg?t=0)
The OpenCase Mounting Kit makes wire management quick and easy!
Lautr3k RepRap
![](https://openbuilds.com/data/article_cat_images/s/0/272.jpg?t=0)
A 3D printer without belts, a print volume of 320x320x260mm, obviously the V-Slot as linear guide! and a maximum of printed pieces.
![C-Beam Machine Too](https://openbuilds.com/data/article_images/l/3/3637.jpg?t=1468614545)
Build Author
Metalguru
Views
13005
C-Beam Machine Too
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
C-Beam Machine upgrade using linear rails to increase machining size by 2.5 times and increase rigidity
![Laser DIY](https://openbuilds.com/data/article_images/l/8/8370.jpg?t=1552059905)
Build Author
holographic
Views
6625
Laser DIY
![](https://openbuilds.com/data/article_cat_images/s/0/303.jpg?t=0)
How i construct and create my DIY Co2 Laser cutter and engraving mashine. details will follow
Large 3D Printer 5ft by 5ft print bed
![](https://openbuilds.com/data/article_cat_images/s/0/272.jpg?t=1389472082)
New ultra large 3D Printer design. I'm calling it the AutoCrafter
![MEGADELTA, TLM CLONE with 500MM bed](https://openbuilds.com/data/article_images/l/8/8257.jpg?t=1549700418)
Build Author
patnap71
Views
5675
MEGADELTA, TLM CLONE with 500MM bed
![](https://openbuilds.com/data/article_cat_images/s/0/272.jpg?t=0)
All metal frame 500mm bed Delta 3D printer
![CNC Coating Machine](https://openbuilds.com/data/article_images/l/7/7953.jpg?t=1543672707)
Build Author
Vegard Humlen
Views
3812
CNC Coating Machine
![](https://openbuilds.com/data/article_cat_images/s/0/295.jpg?t=0)
The purpose of this machine is to mix two parts of conformal coating with different viscosity in exactly 1:1 ratio and distribute the fluid on to PCB to seal and make it waterproof.
OpenBuilds LEAD Machine 1010 40" x 40"
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
Openbuilds LEAD machine 1010 build
Black Rabbit 1500
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
This is a router that I designed that is loosely based on the Openbuilds Ox, but designed to be heavy duty, rigid, and yet quick and agile.
Starting my build 2.8mx1.4m
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=1389472260)
Starting my cnc router, laser and plasma using aluminium 80x80
OoozNest WorkBee
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=0)
A Journey on the WorkBee Build...
WorkLead, no wait, LeadBee, naw... WoodWorker
![](https://openbuilds.com/data/article_cat_images/s/0/286.jpg?t=1389472260)
Improvements on the Lead machine using some Workbee parts
![Loading...](styles/uix/xenforo/widgets/ajaxload.info_B4B4DC_facebook.gif)