Select a Category
Build Author JerwanDavis Views 1006
Coined by my family as the: Davomatic
Build Notes: Here are all the parts necessary to re-produce this design. Please note, all of the parts are either sourced through openbuilds or have been selected and printed from thingiverse.
Build Author Naomi Wu Views 3256
Naomi Wu's Automatic Bartender- BarBot!
This is an automatic bartender- a BarBot, designed to be made with off-the-shelf OpenBuilds, V-slot and low-cost 3D printer parts.
Build Author bpatterson42 Views 625
Inverted Y C-Beam Machine
Similar to C-Beam Machine build, but with inverted Y-axis assembly to shield drive screw. Integrated XZ gantry can be fixed to any solid surface. Build dimensions are 36" x 36" x 6".
Build Author MidnightQuads Views 1301
Components- RAMPS, running marlin, Nema 17, All metal extruder, 600mm lead screws, 600mm 2020 aluminum extrusions, 12v 30a power supply, 12v LED strip, Typical endstops, 600mm 8mm linear rods, Bearing block for 8mm bearings, Openbuilds plates, wheels, and bearings, 500x500mm borosilicate glass plate
Build Author Terone Burgenheim Views 630
This build is my version of the CBeam machine. I opted to NOT use the Gussets, and instead went for the 40, and 60 mil angle brackets to cut the price back a little further. I started with the smoothieboard but decided it was still "too new" and very much experimental. This build took me a few (2-3) days to complete. The CBeams and Lead-Screws really make building things faster since you don't have to clamor over belts.
Build Author Fabio Orsi Views 3011
147 RepStrap 002
This project is focused on developing a low-cost, portable and open-source FDM 3D Printer.
Build Author recoush Views 2850
CoreXY 3D build one
an 8020 build with 1010 extrusion (1") Square tubing Rough size is 24x24x36 (600x600x900) The expected usable print area 21.5x21.5X32"roughly (510x510x760) An XY 3D printer with 3 extruders and 3 Z-axis 0.9 degree motors the table (Z-AXIS) will lift up to the XY Carriage on 3 12mm linear rod and 3 8mm Lead screw's Corexy designs complete and Z-axis build is started don’t have a 3D cad system yet so building my prototypes on a pcb layout tool
Build Author schwabelectronics Views 3485
Vertical Drill Mill
Mill drill using a dremel and some 3d printed parts
Build Author MikeBardsley Views 6767
Fast, Large build area, CoreXY design
Build Author mrtinkerer Views 11825
V-slot and MDF DeltaBot
This is a deltabot 3D printer build using CNC routed MDF and v-slot rails. Full description found in instructables.com.
Build Author Keteland Views 7184
MULIMATERIAL 3D PRINTER (in progress)
ELECTRONICS - ARDUINO Mega 2560 + RAMPS 1.4 + power supply 12V - Leadshine DM 5042 external driver + Power supply 36V + NEMA 23 stepper motor SOFTWARE - Repetier Host to communicate with the Ramps - ARDUINO to upload the firmware (Marlin) MECANIC - V-Slots rails 40x40 + home-made plates - everything goes fine on the side of the build
Build Author nicklogan Views 11783
A Rostock style delta bot with the parts which are typically 3D printed made from medium density fiberboard (MDF). It uses a home made hot end.
Build Author Gamekiller77 Views 2123
Atlas Delta Bot
The idea here is to build a nice large delta bot from the parts ground on the one builds part store. Other parts that are sources out side of this will be detailed. I have a simple BOM I started that I will upload later.
Build Author Sam Dobbie Views 4574
A fully aluminium printer made from off the shelf components, no printed parts.
Build Author Sheepdog Views 20745
Griffin Delta Printer
Designed from the ground up as a low cost, highly scalable delta printer. This printer has been built as small as carry on luggage size, up to an 18in wide print surface and is capable of larger. Approximate cost is low to mid $500 range start to finish, including electronics for a basic model.