I designed this 3D printer from scratch for my mechanical engineering capstone project. It's made for printing clay but should be able to print any paste material. The clay extruder system could be easily modified to work with almost any 3D printer. The printer is approximately the same size as an Ender 3.

Learn to build the V-SLOT Mini V Modular linear Actuator System and create all kinds of cool machines!

I hope to have a working prototype built soon.

Homemade plasma cnc

This is the first project that I would like to share with you. I know the build looks familiar and it is; it’s based on kram242´s Routy. Work area is 300*500*55 mm and is NEMA17/GT2 belt driven.

CoreXY build

From where Mark left off from the Ox build I am going to film the whole process of customizing the Ox.

Steel square tube frame with dual feed gantry and indexing lathe section. Will have 36" x 30" x 6" travel. Has a Harmonic Drive on the 4th Axis.

OneZ gets it's name from it's most unique feature - only motor for the Z axis while maintaining the stability of two bearing guides for the Z axis. Reduction to one Z motor eliminates need for auto bed leveling.

This build uses drawer slides and thread rod to create foam wings and fuselages by passing a hot wire through the foam which makes very accurate shapes. I built a Radio Controlled SuperVC10 using foam but did have a cnc machine then so I had to make many templates to guide the hot wire. This inspired me to build a cnc hot wire cutter. Works really well and have made several RC models with it now

A CNC HVLP spray booth based on OX.

The Smart Laser Mini is an open source such as use Raspberry pi. Easy to assemble type of desktop laser cutter and engraver. Also we used V-slot

A CoreXY/Bowden design with a belt driven Z axis. This is a box design without the front end of the box, making the print area and maintenance, like changing a nozzle, easily accessible.

This is a mount I wanted to build for a laser project using OpenBuilds part router mount.

Low cost Laser Engraver build using all off-the-shelf components.

Currently I have Velleman/3Drag K8200 modified and CNC machine self built and wanted to use both to make new 3D printer. After looking at different designs I liked Voron a lot and have decided to go that way. Currently I have ordered majority of parts and build shall start soon. I don't plan to rush it as I am usually 2 months home and 2 off. Today done some electronics. Looks ok. https://youtu.be/ls_tl54ruE0

Dual X-Carriage CoreXY. Not impossible, but probably the only one. Use the link to Thingiverse "Hlidskjalf" for parts and downloads.

A quick and easy way to make a 3-way mitered corner using MakerLinks

The idea was to build a proof of concept table saw fence similar to a thru-rip or accusquare fences which retail for 400$, with the added option to motorize the positioning.

Simple enclosure for the OB Minimill

A horizontal-router CNC using openbuilds parts geared toward routing out mortise and tenon joinery; or any other end grain work on wood.

I rebuild my 2 meter tall 3D printer into a 100w laser cutter

A modified 1000x1000 Sphinx, with a built in vaccum table.

I took what I thought were the best parts of the sphinx and the c beam xl to build a bigger and faster machine.

Acro based 2 watt laser platform

This is my first CNC build. As per the norm, I went in with months of research, planning, and resource gathering tied neatly together with a solid plan. As the path went on, the plan continued to change to accommodate issues I hadn't counted on. But, at the end of the road, the project reached completion, and I learned a ton along the way!

Light enough for high speed #3dprinting Strong enough for high speed #3dprinting

This is my first CNC router build, so I started with the OpenBuilds C-Beam Machine XLarge mechanical bundle, including four high torque stepper motors. I took my time with the mechanical build, sought and found some great help for my control system, and designed and built a custom cabinet to house everything.

Open builds style wood CNC router. Usable work aria 1000mm x 1250mm x 150MM (X x Y x Z). 80x40 C bleam for the Y axis , two 60x20 beams for X axis and a 60x20 fo Z. Interlocking GT3 belts for X and Y. Looking to change over to a rack and pinion system in the future. 8x8Tr Lead screw for the Z. Leadshine HBS507 close loop drivers and 3-phase servo motor 573HBM20-EC-1000 motors driving the Y and X axis. Would recommend them to anyone looking for servo like performance at a affordable price.

In the design stage. Help guide.

A minimalist 2-axis A2 sized laser diode cutter/engraver. Designed to give the most function using the very least number of parts at the lowest price.

The OpenBuilds Sphinx 1050 - 500x1000 Lead Screw Machine

This will be a slow build as I collect parts and materials as funds permit for 1000mm x 1000mm Workbee. I call it the "Hand Crafted WorkBee" because I will be hand making the plates and as much of the build as possible using a drill press and hand tools.

probably as big as you'd want it...

This was my first foray into CNC. I chose to go with a reliable kit build since my knowledge of GCode, controllers, and steppers was pretty rudimentary.

A 1000 by 1000 CNC Router with linear rails and a control box.

C-Beam machine - 1000mm base.

This is an arcade "cabinet" of sorts built almost entirely from OpenBuilds extrusions. Save for a few 3d printed parts, the electrical components, the acrylic panels, and the monitor mount, every component was purchased from the OpenBuilds part store.

This items are so cool that they need to be together, so I decided to create brackets that connect both pieces together

Create a ball screw carrier with out BF BK bearing blocks.

Ball screw drive, linear rail CNC Kit

Making my own magnetic dust shoe with led lights and a camera. Showing my progress from beginning to now.

A desktop Cartesian CNC router

A framing design for cantilever style printers

lead machine plasma table with Black Box, and Torch Height Control

This is just a small project to get use to the OpenBuild products.

Drag knife and pen holder which mounts in spindle collet.

My on going build of CNC Mini Lathe

A completely belt driven cartesian design with a center mounted X motor. This is a very compact, rugged design.

Learn to build a super strong nema 23 lead driven linear actuator

Here are a few helpful C-Beam actuator ideas that will help you get a start on your builds

This build is inspired by the Lulzbot Taz printers and makes use of the new OpenBuilds C-Beam

In short...this was a fun project.

A Modified and augmented Ooznest C-Beam Machine Plate Maker.

A C-Beam router made almost entirely of standard parts. Electronics include an xPro v2 board and NEMA 23 motors. Cuts are made with a small 300W DC spindle. A pressure foot is used to minimize the need for workholding.

Machined Aluminum MagBall Carriages

This is my CNC build. My goal is to have fun and learn some new things.

A very fun and fulfilling build. I can't say enough about the whole Open Builds site and Open Source movement. I strongly believe this is the fastest and most creative way of getting ideas out of the mind, and onto the floor.

This is an experiment to build a Linear Delta Printer using four towers instead of three. Primary reasons: 1. Build area is roughly cubic vs roughly cylindrical 2. Greater speed and precision from additional control provided by fourth tower. 3. Symmetric kinematics from even number of towers.

This is the story of my experience building a 1000 x 750mm OOZNest OX CNC router

1000mm X 1000mm overhead cnc machine

Laser CNC, 60W, didn't have one yet... have to :) This build is a retrofit of a surgical laser into a CNC.

A 1000mm x 1000mm Sphinx/R7 build.

An Openbuilds replacement rail system for the common eBay "K40" C02 Laser Cutter

A home-made CNC-machine with a 1.5 kW air cooled spindle motor suitable for milling materials such as wood, plastic and soft metals. The work table is 650 mm wide by 700 mm deep and the maximum movement is set to 560 mm for the x-axis, 480 mm for the y-axis and 105 mm for the z-axis.

A 1000mm x 1000mm copy of Kyo's Sphinx

DO WHAT YOU IMAGINE !

The Tiger Paw will be a 1000mm X 500mm Cartesian style CNC with the Minimill attached to the end. It is named the D&R Tiger Paw because my son, Daniel, and myself, Richard, will put this Tiger strong and fast machine together. Our goal is to have a Tiger strong build with a Paw print that wouldn’t take up a huge amount of space in our garage.

The Acro Laser Machine Build

This is a modification I made to my Voxel Ox 3D Printer Z axis, which synchronizes the Z leadscrews via a shaft and helical gear transmission. It prevents the two Z leadscrew from getting out of adjustment relative to each other, and uses a single Z motor instead of two. This build is just documenting the specific changes I have made to the Z-axis, since the frame and other axes are still from the original Voxel Ox design.

The OpenBuilds Sphinx 55 - 500x500 Lead Screw Machine

I'd like to renew my cnc for PCB so I decide to create new one from an existing project named Cyclone PCB Factory.

A log of my "brain surgery" on a Cricut Expressions 2 to change the control board to something open so that I could cut what I wanted. The ESP32 GRBL board I used has bluetooth and WIFI built-in and was very easy to get working just the way I wanted.

A proper CNC mill conversion. But quite small, with my trademark idiosyncracies.

A 1.9 x 1 m table that uses a magnet to move a steel ball and draw geometric patterns in sand. The magnet is moved using a corexy mechanism driven by 3D printer controller board reading the patterns in the form of gcode files.

The k40 cube is a laser cutter build using mostly stock parts of the chinese k40 laser

This is a build log of the Openbuilds Sphinx 55 with some 3D printed parts for the electronics and probably other parts as they come up.

The machine is a stock Lead CNC, with the Black Box controller and StepperOnline 269oz NEMA 23 motors. I'll be using the DeWalt 611 from Openbuilds, as well.

I am satisfied with my build and next one will be even better.

My First major improvement was changing the controller to a Acorn board. I loved the way a dedicated userinterface was speeding up my workflow. Next project my Y Axis. On Aliexpress I ordered a couple of 16mm ballscrews and some lineair rail. Before I took my gantry off I quickly made some aluminium profiles to fit my carriages. Withouth any doubt these improvements where worth it

Upgrading printers for Synchronous Leveling

A short description of the dust shoe I made for my machine.

Based on the popular C-beam / V-wheel design, with the largest available work area, relative to machine size. Screw driven with anti-backlash, integrated drag chains, Carbon fibre gantry plates, Openbuilds BlackBox Controller (USB), Transformer & kill switches, with internal wiring, limit switches & Nema 23 motors.

Tried to get best value and minimal footprint!

Contains a further modification to Creality's poor CR-10 design

Machine with 12,5Nm closed loop steppers or servo steppers

It began with creating an extremely rigid axis that incorporates a multi C-Beam Linear Rail system as well as precision lead screws coupled with a tension system for the absolute maximum in performance.

We want to present you the new design of the device which is Router Sled. The whole structure is made of aluminum elements and ensures good quality of the device. We used V-SLOT aluminum profiles and OpenBuilds accessories for the construction. The instructional video can be found on our YouTube channel (subtitles in English soon)

Simple Swing Arm Build for the Modular Table Series. Create a simple vacuum swing arm that swings over your machine keeping your vacuum hose and router cord, etc. up and out of the way

Super cool standalone Human-Machine Interface for controlling your CNC machines!

Build Summary updated after parts list completed

A simple vacuum hold down/clamp set up using a 6hp canister vacuum.

We are introducing the Cairo Mini 3d-printer! It’s a DIY fully Open-source Reproducible 20x20cm 3d-printer. The original goal of the Cairo Mini 3d-printer is to create a low-cost 3d-printer below 220$(3500 LE). That anyone can build with ease.

An ACRO laser put together with some repurposed and some new parts.

Quick and Simple V-Slot Gantry System. This example build shows how easy it is to make a linear actuator using a few OpenBuilds Parts. You can mount this system an many ways so be sure to download the example models.

This build was very complex due to the fact I wanted to create a low cost larger than normal CNC. I did not want a MDF or plastic body. I wanted it to be able to do more than most CNC routers this size on the market.

This build is the documentation of someone with no experience building the OX cnc machine with a Gecko G540 controller and CNClinux

Delta printer designed in sketchup and includes an adjustable bed.

This is my OX CNC router. It has been a labor of love for over a year now! I hope you find it interesting and inspiring! I also hope that it gives some of you more experienced CNC builders a different perspective and some ideas!

A new mini version of the http://openbuilds.com/builds/openbuilds-freeburn-1-v-slot-co2-laser-60-100w.1001/ FreeBurn CO2 Lasercutter