This build is to show what's possible as well with openBuilds! I use a single ArduinoMega and 5 separate stepper drivers (A4988). The LEDs are all NeoPixels. Collision 'detection' is all done within the code, so the endstops are only sensors I use in this build. I'm a self-employed video-artist and this is my first installation which just needs power and it runs (where I'm quite proud of). Normally my interactive installations take a long setup time, so this installation is a relief :)

Big brother of the Charging Ox CNC machine.

A stock C-Beam with a CNC shield with DRV8825's

Hello ! This is my very first OpenBuilds build. It's based on the Maximus 3D Printer, published by mytechno3d : good source of inspiration !

This slider uses an 500mm OpenBuilds C-beam and the design is such that the effective length of the slider is slightly less then twice the length of the C-Beam. It can be used both motorized or not.

A CNC platform designed with swapable heads to do laser engraving/etching/cutting, routing and milling, as well as 3D printing.

UltiBots LLC designs and packages DeltaBot 3D printers using quality components. Our kits are V-Slot based. Print results are impressive. The Metal MagBall Carriage was designed to be ridged, compact, and simple.

3d printed V-Slot Gantry Plate leveler.

After expanding a Shapeoko 2 with the rails and motors left over, make yourself a laser engraver.

A 3D Scanning Station

This a redesign of the Folger-Tech Y-Carriage using the Solid V-Wheels, Ball Bearings, the V-Slot Rail System.

Using the Routy290 build and an awful lot of help from puntoMX, this machine has been expanded in the X and Y axis. My first build, I'm learning a lot about all of this. I've had to disassemble parts of this thing many times due to forgetfulness, but that's ok. Also, I've forgotten to take constant pictures throughout the build.

An easy simple Tape Dispenser, spawned out of necessity, and shared for the fun of it...

www.cncforeveryone.com. the Duck is something that i think would be helpful in my shop since we already do cold casting.

This is my build of Niko's (gianakop) Egg Painter. Egg decorating is something many Christians do for Easter Sunday and the Easter (Paschal) Season that follows. This will be my initial use for the build, but also with minimal modification to be able to write/paint on other round objects like Christmas ornaments, coffee mugs, etc. Many people also decorate eggs for purely secular reasons.

After seeing different egg bots designs, I decided to incorporate my own design.

Another build based on the venerable OX. xPRO CNC controller, and a few extras.

This is a PCB designed to control a laser Engraver CNC

Large 6 x 10 foot laser table build. New to building CNC

Optical home and limit switches for cnc, 3D printers, laser cutters, etc.

This is a big 609 x 609 x 914 3d pritner with exchangable hot ends and extruders.

An easy Epic Win for novice engineers new to the RepRap project www.3distributed.com

Build Start to begin Feb 1st.

This is Fina; My Lautr3k inspired build.

It took me 18 long nights to build it

Modded OX with full nema23 4 point support

Out with the Old in with the New. Trying to build a nice clean setup that myself and my sons can use and enjoy.

Low cost, apple crate framed CNC.

The Ronin OX is a dedicated fiber composite milling machine. I give a complete in-depth article on how to take a nearly stock OX build and easily turn it into something that can mill carbon fiber and G10 plate effectively and quickly.

In this, the final part, I would like to introduce Machine Vision and show how it can be used, not only for tool position setting but also for resolving the triangle to calculate the G68 (local system rotated) for jobs which are not squarely placed on the work table.

This is my second Ox with a working area of 14" x 14" x 5" I wanted to build a small sturdy potable CNC router and this OxZilla has the nice upgrades !

This is my story about my need for a CNC router on a budget that wound up in the $5K range !!! but I have a good belt drive Ox

My very first attempt at a CNC build. Based on the OpenBuilds C-Beam Machine, small tweaks will be made to tailor it for my goals: machining G10, aluminum & some carbon fiber for use with multirotor and motorcycle parts. I am looking forward to the day when I am comfortable enough to bring the ideas in my head to the tip of the end mill in a smooth fashion...

OX 1500mm x 1500mm w/1.5Kw Water Cooled Spindle & VFD ran by a Gecko G540 & Mach3

A System of 3d printed parts to use along with your projects aluminum extrusion to cut your pieces of v-slot to length manually.

build is in process the machine went together perfectly no issues at all but the software is another issue I have been trying to get the thing dialed in it is driving me nuts I'm still in the process will update if I ever get it figured out

750mm x 750mm OX build, xPro V2 controller, 400W Spindle with PWM controller.

Leveling Platform / Stand 3D Printers

The STEAM Crane 3d printer uses the new C-Beam linear rail. It is being developed for an after school / summer camp program for kids. All of the electronics are housed in the base and the wiring is routed down the channels of the c-beam. This is done to contain as much of the loose wiring as possible, hopefully keeping it safer for kids.

A fully aluminium printer made from off the shelf components, no printed parts.

Mag arm deltabot with laser cut carriages and connectors.

i had som left over parts and i dit like to test the corexy control so this is wat i came up with. sorry bad englich.

A compact, enclosed Core XY design, based on off-the-shelf parts.

I ran across the OX and knew it was the one I wanted to build. Some of the things I wanted to include was make it bigger and a little more solid than what the original plans called for. So here is where I am at so far. It will have a cutting area of 48" x 48". The waste board support frame will have more support rails. The Y axis will have (3) 20mm x 60mm rails instead of the original (2) that is called for. 1/4" aluminum OX plates. And a few more odds and ends.

An X-Y Stage created from two self contained acme screw linear actuators. This build was published as an example of how many of the OpenBuilds Parts can be used.

Small Form factor based 3 axis Gantry style mill, Removeable mechanical module. Removable Electronics. with a removable machine pallet, for automation.

Build the efficient and reliable all metal structure 3D Printer. Improved significantly with new concepts for printers. Great quality and up to 400 mm/s print speed (very fast). Built with heated bed, hybrid bowden suspended extruder, and counterweight (tested printing 21 hours straight with no motors hot). Optional smart controller for computerless printing. Print any kind of thermoplastic.

LASER ENGRAVING DIY 60 WATT

The new C-Beam kit expanded to 1000mm . extra support built in for the extents of the travel.

The frame is made from all open builds parts, add the rubber feet and pads for the glass. The glass is clear 12" x 16" x 1/4" with a polished edge. A light basket slides on the countertop.

Creating a CNC mitre (45°) cutter, for picture frame cutting. Starting with an OX, but inverting various parts and adding a material table, with a stepper-controlled measuring guide.

This build is very straight forward. The design is simple. There is a great support community for Delta 3D printers.

Yet Another Openbuilds Router, my version :-)

Hell Yeah

This is the largest printer I have found. It is also the cheapest. The reason is that it is run by hand, without computer or motors or electronics. Put an object on one side and move the 3d pen while tracing the object. Move the z dimension by turning the crank on the lab jack to move the printed copy down a notch. Be creative!

Open build rovo 1000mm * 1000mm. (Rovo x ver) 20.06.2015 now in progress. rovo kit is the 10th product. 8th rovo 750,9 th rovo1000, 10th rovo x ver progress at the same time. 10th item is an aspect of 1000. It changes the size and z-axis has been up.

Planning my first build. Hope to achieve a larger format yet rigid design.

Great bit of kit time will tell if it is up to the job

Delta printer, Bed size 280 cm dimeter Print Height 300 cm not tested yet the speed

A work in progress. working to refine the print head/carriage to integrate a bed level probe directly into the print head.

This is a basic description of my OX-like build of Babe, Paul Bunyan's Blue Ox. It is a work in progress. The idea has been germinating for about 4 years, with several twists and turns and false starts along the way.

A complete CNC newbie is tackling a mighty challenge, Not only is he making a CNC router, He's going to try and upsize it.

Proteus is the Greek God of change. Besides the numerous aspect of 3D printing that this could relate to this machine like the god can change. The Build allows for an interchanging head that will allow different functionality to be quickly and easily adapted. So you could print clay, silicon, plastic, cut with a laser cutter or even attach a rotary tool

I creat a open source 3D Printer to print big things. Print size: 400x500x300 mm. You can download the Drawing in PDF and in Inventor 2013 format. The unwinding drawings are also included. I take some detail photos for a better understanding.

This is just a small project to get use to the OpenBuild products.

Rigid 3d printer with more than enough room for dual extruders. Easily expandable platform.

A bigger OX. As this build is nothing new I will detail my build process, I am not an experienced builder, this will maybe help someone else. The size of the bOX will be 100cmx75cm. I will use aluminium plates, a tinyG, and most probably only open source / free software.

OpenBuilds CNC 500x500

This is a 1500 x 1500 Ox build

This is the story of my progression from the JGRO cnc router design to using the OpenBuild system. In the process I think I have learned some things about cnc routers and the accuracy required to make a good build.

Building the full size OX.

SMD AVR Solderless Daughter Board

A practical rotating and stand-alone spool holder which fits any filament extrusion 3D-printer. Several base files provided which make it fit different extruded aluminium profiles.

This is where I will share my attempt at building a slightly "beefier" OpenBuilds OX CNC Machine using commonly available parts in the spirit of OPENBUILDS and Open Source in general. I have a tendancy to over-build things so I will be balancing that tendacy against budget constraints and common sense as much as possible.

My first Build with V-slot

Just an easy build .... uncomplicated.... simple tools .... but hoping for a good result!

A 1000 x 1500 OX build with the ability to router cut dovetails as well as laser engraving and light cutting.

Large leveling platform to hold a 3hp router

Mechanically, a scaled up OX build (1500x1500). Electronically, GRBL on an Arduino and a gShield. From a software perspective, the focus is on useable open source software tool chains.

Acquiring a CNC has been on my list for some time now. This concept is a bare bones, upgradeable machine that will not require a complete rebuild when new parts become available. With a cutting surface over 36" square, this beast should be capable of creating its own parts. Lowering the price to make upgrading and making this contraption beefier, faster, and more precise.

I've been working on commercial woodworking CNC's for year's under shop owner's that didn't want me to progress any further at a certain point. This is a project I've wanting to build for about 10 years now. I can't wait for the freedom to build what I know is possible without any negative input.

Now test ready

OX MultiMachine

Multi-tool 3D printer, laser cutter, and CNC mill.

I have been looking for a good solid kit to build off of for some time and when I saw the Ox buildlog I knew I had to have one. Ordered most of the pieces from Open Builds and started planning. Had a nice gentleman named Chris cut the required plates from 6061 aluminum for me (he sells them on eBay now if you're interested) and got to work.

Realisation of my idea about a foldable collector for rainwater, which is light and easy to make. People around the world need water and can collect rain water with this collector. I made it for syria and all too.

CNC MILLING ROUTER

This is a work in progress(not printing yet). Expect this instructions to grow with time, but for now it is mainly interesting for those who want to take part in developing this printer.

www.cncforeveryone.com TITAN CNC ROUTER is the perfect PCB milling machine or for smaller projects. Don't be fooled by its small size it is capable of routing with the big boys...!

The method used for tool position setting is a matter of personal choice but this is what I do.

A simple low cost rotomolder.

As a 3rd year mechatronic engineer with a plan to print my 4th year thesis project and with no elegant backup plan, I ran into a problem, I'm gonna need a bigger printer. Loving the DeltaPrintr kickstarter, but needing it before the end of next year I have resolved to make my own.

A little project for a rainy day which some, like me, may find useful.

All's good for assembly, testing coming up soon