Welcome to Our Community

Some features disabled for guests. Register Today.

Eddie's Build of Niko's (gianakop) Egg Painter

Discussion in 'DrawBot' started by eddiejr, Mar 19, 2016.

  1. eddiejr

    eddiejr New
    Builder

    Joined:
    Feb 15, 2016
    Messages:
    73
    Likes Received:
    9
    eddiejr published a new build:

    Read more about this build...
     
    #1 eddiejr, Mar 19, 2016
    Last edited: Mar 22, 2016
  2. eddiejr

    eddiejr New
    Builder

    Joined:
    Feb 15, 2016
    Messages:
    73
    Likes Received:
    9
    [ This space reserved. ]



    Potentially Useful links...

    Niko's Egg-painter robot (OpenBuilds) by @gianakop on openbuilds.com

    Niko's Egg-painter robot (OpenBuilds) by gianakop on thingiverse.com

    Egg-painter Build by @Slobberknocker on openbuilds.com

    Pen Holder for Eggbot by Geotek in thingiverse.com

    V-Slot SphereBot by @Mark Carew on openbuilds.com

    EggBot Software from evil-mad on github.com

    The Original Eggbot - Basic Setup and Your First Plot Tutorial by Evil Mad Scientist on youtube.com

    EBB (EiBotBoard) website by Brian Schmalz of schmalzhaus.com

    Don't want to build your own? Just buy... The EggBot Pro.

    EggBot "mods" and other parts from EMS.

    Inkscape
     
    #2 eddiejr, Mar 19, 2016
    Last edited: Mar 26, 2016
  3. eddiejr

    eddiejr New
    Builder

    Joined:
    Feb 15, 2016
    Messages:
    73
    Likes Received:
    9
    20160322_145638_cr.jpg
    This is how the "egg holding part" is looking without "the sticky tack". I have not added the pen holder or the electronics yet.
     
  4. eddiejr

    eddiejr New
    Builder

    Joined:
    Feb 15, 2016
    Messages:
    73
    Likes Received:
    9
    Thanks. Hopefully these pictures will help.

    20160323_222209.jpg 20160323_222522.jpg
     
    JustinTime likes this.
  5. eddiejr

    eddiejr New
    Builder

    Joined:
    Feb 15, 2016
    Messages:
    73
    Likes Received:
    9
    #5 eddiejr, Mar 24, 2016
    Last edited: Mar 24, 2016
  6. eddiejr

    eddiejr New
    Builder

    Joined:
    Feb 15, 2016
    Messages:
    73
    Likes Received:
    9
    Here's how the pen holder is looking. I had to "stagger" those fine screws on the distal end of the hinge because I somehow snapped a screw head off when tightening. I've updated the BOM (parts list).

    20160326_171901_cr.jpg 20160326_171941_cr.jpg 20160326_154458_cr.jpg
     
    #6 eddiejr, Mar 26, 2016
    Last edited: Mar 26, 2016
    Mark Carew likes this.
  7. eddiejr

    eddiejr New
    Builder

    Joined:
    Feb 15, 2016
    Messages:
    73
    Likes Received:
    9
    I connected the electronics together, but need to double-check again before I turn on the power. The power supply I will use is from a Linksys E3000 and seems to fit the board connector well.

    20160326_201046_cr.jpg 20160326_201003_cr.jpg
     
  8. eddiejr

    eddiejr New
    Builder

    Joined:
    Feb 15, 2016
    Messages:
    73
    Likes Received:
    9
    Here's it looks put together. I accidentally ordered two nema17 motor plates, but will replace one nema17 plate with a nema23 plate in the near future. Will install Inkscape v0.91 and the EBB software v2.50.

    20160326_173438_cr.jpg
     

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice