Select a Category
Build Author Lumberjack Engineering Views 16959
SOLAC: Space Optimized LAser Cutter
The Space Optimized LAser Cutter is a 40 watt CO2 laser cutter that supports a maximum part volume of 24" x 16" x 6.25". It consists of a V-slot frame + brackets/mounts designed to be 3D printed on a consumer desktop printer. Total cost of the machine is ~ $1,400 USD.
Build Author jz321 Views 3061
OTiS (Off The Shelf) is 500mm cartesian CNC that can be built with all off the shelf parts from OpenBuildsStore. It features C-Beam actuators and a V-Slot frame.
Build Author James Evanko Views 4699
Laser Displacement Golf Ball Scanner
Getting an accurate scan of a golf ball can be difficult with general-purpose 3D scanners. This purpose-built golf ball scanner uses a very accurate Keyence LK-081 laser displacement sensor with an Open Builds linear actuator for the vertical axis and a Sherline CNC rotary table for the turntable. Scan detail is determined by the sample step size and can be set arbitrarily based on desired scan time.
Build Author rkugler Views 4672
Miter Saw Stop Block
Just starting a miter saw stop system. Any suggestions appreciated.
Build Author GDanger117 Views 8303
Gantry CNC - Decisions made only to change over and over.
This is my first CNC build. As per the norm, I went in with months of research, planning, and resource gathering tied neatly together with a solid plan. As the path went on, the plan continued to change to accommodate issues I hadn't counted on. But, at the end of the road, the project reached completion, and I learned a ton along the way!
Build Author Srđan Marković Views 2633
Machine with 12,5Nm closed loop steppers or servo steppers
Build Author Rob Taylor Views 7735
Grizzly G0758 Benchtop Mill Conversion
A proper CNC mill conversion. But quite small, with my trademark idiosyncracies.
Build Author Calotype Views 2238
My DIY panoramic rolling (&banding) Machine.
DO WHAT YOU IMAGINE !
Build Author Savvas Views 15211
CNC Control Box with VFD etc etc
I'm currently working on the CNC control box, before doing any future work on the CNC Mountain Machine. I want the controller to be future proof and as professional as I can manage. I am planning to use stepper drivers, PSU's, a motor contactor unit to turn everything on, as well as a VFD and proximity limits switches. Each video will document the process and steps involved in researching, designing, planning and assembling a controller. I am not a natural electrician so learning as I go.
Build Author Gerrald Views 4201
This build is to show what's possible as well with openBuilds! I use a single ArduinoMega and 5 separate stepper drivers (A4988). The LEDs are all NeoPixels. Collision 'detection' is all done within the code, so the endstops are only sensors I use in this build. I'm a self-employed video-artist and this is my first installation which just needs power and it runs (where I'm quite proud of). Normally my interactive installations take a long setup time, so this installation is a relief :)
Build Author ChrisViral Views 4858
OP C-Beam Machine XL by ChrisViral
Video diary C-Beam XL build with massive steppers and a 1.5kW Chinese spindle.
Build Author Venturebit Views 9143
SHRED-Buddy3D UPcycler - Open Source Multi Material Cutter&Pelletizer
The whole system is powered by 12V / DC power. Process it into Pellets or Granules to use it with your 3D Printer or Filament Extruder. Our self-developed steppermotor Controls allows you to optimally adjust Feedrate for your Situation. Forward, Backward and Stop is integrated for easy operation. The Speed can be continuously regulated via rotary switch.
Build Author James Evanko Views 2387
Sherline C-Beam with Offline Controller and MPG
This is a C-Beam based router with V-rails used for the bed, a Sherline spindle with Jacobs chuck, closed loop stepper motors on every axis and an offline 4-axis CNC controller. A U-channel was created to guide the drag chain on the X-axis.
Build Author Jacob Lotter Views 3269
CNC ESS Controls System
My Controls box to run my Workbee 1510 That was retrofitted with Lead Screws as well as Lineal Bearings. The stock electrical configuration was not enough, so here are the Measures that I took to not only make this machine Run again, but to have fun with it, and make this system be able to run any CNC I run in the future with the installed microcontroller.
Build Author Rwetzler Views 7542
This is a variant of a typical OX (Mark Carew inspiration) router using C-Beams/8mm Acme rods to drive all three axis. I went with a 1000mm x 1000mm frame size. Useable space is 28" (711mm) X 26" (660mm) with a Z axis work travel of approx. 3.25" (82.5mm). A TinyG is used as a controller along with Fusion 360/Chilipper as the software for generating and running gcode files.
Build Author M^3 Views 15687
M Cubed 3 Axis Bluetooth CNC Controller
Low cost, Bluetooth enabled, 3 axis CNC controller. GRBL 0.9 compatible.
Build Author Neptunes Guitars Views 6798
First build of CNC OX for the purpose of using it for Guitar building to take a lot of the muscle work out so I can concentrate on the finer details.
Build Author stepper Views 2688
Touch screen macro imaging
This is a brief overview of the build of my macro imaging slide.
Build Author mikev Views 7108
C-Beam Evolution MkII
The C-Beam Evolution is an evolving machine. The MkII is inspired by Kyo's C-Beam Spinx but currently uses my own design of plates made of 8mm acrylic (X-axis ends) and 6mm polycarbonate (Y axis ends). The plates were made on the MkI but I hope to be able to make 6mm aluminium plates on the MkII for the MkIII.
Build Author James Evanko Views 2501
Ball Trajectory Machine
Need to build a machine that accurately positions objects for processing by a computer vision algorithm? Here is an example of a machine that does that for a ball trajectory application. The black anodized V-rails work well for applications in optics and imaging where the machine needs to stay out of the limelight.
Build Author Craig Hollabaugh Views 2986
Hyatt and My Journey to Tonehenge
I'm conducing guitar loudspeaker cabinet fabrication technique research (material type/thickness, mechanical joints, adhesives, etc) and how these relate to cabinet/speaker coupling and enclosure resonance with respect to psycho-acoustics. Basically, does one speaker cab sound better than another and why?
glue/staple/eject 1 Axis driven Rail building machine.
Build Author Robert E. Nee Views 13567
Large cartesian gantry style 3D printer
This will be a fixed bed, v-slot implemented X,Y,Z axis gantry style 3D printer.
Build Author Mallemann Views 2833
Generic 6 Axis Controller
Generic 6 Axis (Stepper) Controller
Build Author Vin1027 Views 5298
This is the original C-Beam Sphinx with the 16 wheel X gantry plates. I'm using the Ethernet Smoothstepper, Gecko G540 stepper driver and Mach 4 for motion control.
Build Author SCYBUCK Views 3813
KYO SPHINX a la' SCYBUCK
KYO SPHINX, CENTROID ACORN, GECKO 540, HALL EFFECT LIMIT SWITCHES, 2.2 KW, 24,000 RPM SPINDLE, WATER COOLED, 600 oz-in STEPPERS, INTENDED TO CUT ALUMINUM.
Build Author Crazzy French Dude Views 2665
PeeNaPle_V1.4b is a BoB controller board for 3D Printers, CnC and cartesian machine, using the latest Teensy_4.1
Build Author Mogens Kusk Views 4116
Belt driven 1200mm x 700mm x170mm axis
Build Author Ken376 Views 2422
Welded project cnc first try
Kind of hard to see in this pic now lining up drive s and finishing framework