Welcome to Our Community

Some features disabled for guests. Register Today.

Sign Up

limit switch

Page 1 of 2
  1. Osmond
    Thread

    X Limit Always Triggered

    Hey all, Can someone help me figure out why my x-limit switch is being triggered? I have switched the endstop and switched it around with the...
    Thread by: Osmond, Feb 14, 2023, 8 replies, in forum: CNC Mills/Routers
  2. Oscar Mejia
    Thread

    Would 4-wire Limit switch work with BlackBox?

    Hi All, I have some Inductive Limit Switch PNP NC to use in my router table build: 12mm Inductive Limit Switch PNP NC The Blackbox has 3-wire...
    Thread by: Oscar Mejia, Jan 17, 2023, 1 replies, in forum: CNC Mills/Routers
  3. Michael Bauer
    Thread

    Gantry strikes Limit Switch hard

    Good day, I have recently purchased and assembled a Lead 1515 and am running into a single issue with the X axis when Homing. The Gantry activates...
    Thread by: Michael Bauer, Jan 3, 2023, 7 replies, in forum: CNC Mills/Routers
  4. TimmyTime
    Thread

    Setting limits to NC on Openbuilds Control

    Hey there, looking to set up an existing Gravotech IS7000 that has NC limit switches and just looking for a setting in Control software. Work has...
    Thread by: TimmyTime, Oct 11, 2022, 1 replies, in forum: OpenBuilds Forum Help
  5. JohnnyWing
    Thread

    Limit switch alerts trigger twice?

    New 1515 build here. Everything appears to be running fine but every time I hit a limit switch (Copperpour Xtension Limit Switch Kit), I must...
    Thread by: JohnnyWing, Feb 4, 2022, 2 replies, in forum: CNC Mills/Routers
  6. Steve French 17
    Thread

    Limit switches will work one at a time, but not when wired in paralell

    I wired my limit switches as per the instructions here (so I can have a limit switch at the min and max point of the axis)...
    Thread by: Steve French 17, Dec 2, 2021, 4 replies, in forum: CNC Mills/Routers
  7. dbdb
    Thread

    Limit Switch problem with Blackbox

    Limit switch x & y (I assume z also) do not stop machine. 1) traced wiring, looks correct again 2) I hand triggered x, y and z and see the...
    Thread by: dbdb, Jul 26, 2021, 3 replies, in forum: General Talk
  8. Daniel Thackeray
    Thread

    Strange limit switch problem

    I am running a 2D plotter using GRBL and UNO. One limit switch isn't working and I can't figure out why. The X-axis limit switch is always read...
    Thread by: Daniel Thackeray, Feb 26, 2021, 3 replies, in forum: 3D printers
  9. Pok3
    Thread

    Limit switch always on

    Just finished my build of the Lead 1515. The one limit switch (Z in this case) always shows on. I've double-checked the wiring and if I connect...
    Thread by: Pok3, Jan 27, 2021, 1 replies, in forum: General Electronics
  10. Jolly_Greem_Giant
    Thread

    Workbee Limit Switches Not Stopping Motors

    Hi I have just built a workbee 1000mm x 750mm screwdrive and have an issue with the limit switches. The limit switches do not cut the motors. The...
    Thread by: Jolly_Greem_Giant, Jan 26, 2021, 9 replies, in forum: CNC Mills/Routers
  11. StuartD
    Thread

    NPN Normally Open Inductive Sensor - will signal fry blackbox

    Hello, I intend to connect in a 6-36V NPN NO Inductive Sensor to the Blackbox. The vendor has provided the following wiring diagram: [ATTACH] I...
    Thread by: StuartD, Dec 31, 2020, 41 replies, in forum: Controller Boards
  12. mattjones99
    Thread

    XTension limit switches 2 wire?

    Hello, I have 2 wires already threaded through for the limit switches, but I I'd like to purchase the XTension limit switches. Can these be used...
    Thread by: mattjones99, Dec 7, 2020, 10 replies, in forum: General Talk
  13. Stacey Miller
    Thread

    Homing Cycle not working

    I am new member ( a couple weeks) and just wanted to say Thank you all. Have a quick question My Workbee is from SPAM 3d but I went with the...
    Thread by: Stacey Miller, Sep 3, 2020, 1 replies, in forum: General Talk
  14. Simon.Jackson
    Thread

    Ooznest workbee Xpro v3 limit switches

    Hi guys, I purchased a used Workbee belt driven on the Y axis and screw on the X and Z. its has the obsolete Vpro v3 board. I've had a nightmare...
    Thread by: Simon.Jackson, Jun 19, 2020, 14 replies, in forum: General Talk
  15. Mike Nieman
    Thread

    Broke 2 limit switches

    I am new with my 1050 and did my first project. I surfaced my spoilboard using the Openbuilds Control program. I first checked to make sure each...
    Thread by: Mike Nieman, May 19, 2020, 3 replies, in forum: CNC Mills/Routers
  16. com3
    Thread

    Blackbox Limit Switch positions

    Hey Openbuilds Community, I just finished my small CNC build and was wondering where to position the limit switches. Currently I got one in the...
    Thread by: com3, Jan 24, 2020, 4 replies, in forum: Controller Boards
  17. doug@towerleather
    Thread

    Limit switches - Normally Open Vs. Normally Closed

    Hi folks, I just picked up several Xtension limit switches to replace some damaged micro switches. I originally had my switches Normally Closed....
    Thread by: [email protected], Oct 24, 2019, 8 replies, in forum: Controller Boards
  18. SpringBob
    Thread

    Z Axis Limit Switch Mounting

    Could someone show me some examples of mounting limit switches for Z axis home/safety limit? Some pics or point me to a thread or two! Appreciate...
    Thread by: SpringBob, Apr 4, 2019, 5 replies, in forum: CNC Mills/Routers
  19. Willis
    Thread

    Z limit switch on a 2.5D machine

    I am making my first foray into CNC machining with an old Amdek plotter and running GRBL on an Arduino Uno. So far everything works great and I...
    Thread by: Willis, Mar 28, 2019, 2 replies, in forum: General Talk
  20. Tracy Ranson
    Resource

    Temco CN0097 Limit Switch Mounts 2018-12-29

    [ATTACH] [ATTACH] I needed a decent solution for mounting the Temco CN0097 limit switches that I purchased on eBay. The options that are...
    Posted By: Tracy Ranson, Dec 29, 2018 in category: Parts
Showing results 1 to 20 of 27
Page 1 of 2
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice