Welcome to Our Community

Some features disabled for guests. Register Today.

Sign Up

lead 1515

Page 1 of 2
  1. Ethan Maloy
    Thread

    Openbuilds interface gets stuck sending job.

    I got my interface set up today to run a job so that my laptop would not be tied up for 6 hours on the job. After some issues with the naming...
    Thread by: Ethan Maloy, May 23, 2024, 2 replies, in forum: Interfaces
  2. Maskido
    Thread

    Circle cutting issue

    Hi there, I'm having an issue when cutting circles on my lead 1515. The start/stop point creates a indent regardless of which bit I'm using. All...
    Thread by: Maskido, Apr 24, 2024, 3 replies, in forum: CNC Mills/Routers
  3. Maximilian Zödl
    Thread

    LEAD 15 Rotary Upgrade

    Hello, i want to install a rotary axis on my Lead 15. Are there any suitable stepper motors (which are available in the EU) and what do i need to...
    Thread by: Maximilian Zödl, Aug 28, 2023, 1 replies, in forum: CNC Mills/Routers
  4. Maximilian Zödl
    Thread

    Router11 Installation

    Hello there, i was wondering if there are any possibilities to connect my Router to my blackbox so the program can turn it on and off itself and i...
    Thread by: Maximilian Zödl, Jun 26, 2023, 5 replies, in forum: CNC Mills/Routers
  5. Maximilian Zödl
    Thread

    Y-Axis squareness

    Hello! Today i set up my 1515 and so far it is looking good. But now i have one thing to do and that is squaring my Y-axis so both gantries are on...
    Thread by: Maximilian Zödl, Jun 23, 2023, 1 replies, in forum: CNC Mills/Routers
  6. TC Follansbee
    Thread

    Issues with accuracy

    Openbuilds lead 1515 running router11. 1/4 compression bit. Cutting whisky smokers out, pretty simplistic design with 3 ovals. The problem is that...
    Thread by: TC Follansbee, Apr 27, 2023, 8 replies, in forum: CNC Mills/Routers
  7. Michael Bauer
    Thread

    Gantry strikes Limit Switch hard

    Good day, I have recently purchased and assembled a Lead 1515 and am running into a single issue with the X axis when Homing. The Gantry activates...
    Thread by: Michael Bauer, Jan 3, 2023, 7 replies, in forum: CNC Mills/Routers
  8. Brandyn
    Thread

    Bit went further down the further out it went.

    I was doing a circle pocket 1/4" deep in 1" material using a 1/4" upcut, was cutting at a depth of .25, basically it was this round piece of pine,...
    Thread by: Brandyn, Dec 3, 2022, 5 replies, in forum: CNC Mills/Routers
  9. Brian Hagen
    Thread

    Jogging measurements Interface Touch with black box

    I have been building my Lead 1515 for about a year now and am in the final stages. I am using the Interface Touch with the black box and...
    Thread by: Brian Hagen, Nov 12, 2022, 2 replies, in forum: CNC Mills/Routers
  10. Tj Ellison
    Thread

    Open Builds Lead 1515 X Axis Please Help (video)

    My lead 1515 x axis is binding I have done everything I know to fix it it keeps binding I’ve ran the lead screw with a drill I’ve use silicone...
    Thread by: Tj Ellison, Oct 7, 2022, 3 replies, in forum: CNC Mills/Routers
  11. Tarquynn
    Thread

    Blackbox, No toolhead connector, Relay for IOT?

    First post. I finished my Lead 1515 build, got everything running smooth, and built up a small dust collection system. I got an IOT relay, but...
    Thread by: Tarquynn, Jul 26, 2022, 15 replies, in forum: OpenBuilds Forum Help
  12. Evilspawn
    Thread

    Tramming Suggestions

    I'm trying to tram my spindle on my Lead 1515 and I'm running into some issues figuring out the best/easiest way to go about it. I'm getting steps...
    Thread by: Evilspawn, Jul 3, 2022, 2 replies, in forum: CNC Mills/Routers
  13. Jay Giroux
    Thread

    Lost Connection to Wifi - Blackbox for LEAD 1515

    I've somehow lost connection to wifi on my Blackbox connected to my LEAD 1515. I did not set up the unit, so I'm very new to trouble shooting this...
    Thread by: Jay Giroux, May 10, 2022, 17 replies, in forum: Control Software
  14. Tterbo
    Thread

    Z Axis gradually rising during build

    Hello all, Sorry if this is post is duplicative but I couldn't find another post that had this specific question. My issue may be weird in that...
    Thread by: Tterbo, May 1, 2022, 5 replies, in forum: CNC Mills/Routers
  15. cjc0306
    Thread

    Meshcam and Lead 1515 compatibility issues

    Help! I have a Lead 1515, Meshcam v8.49, and Openbuilds Control. I cant get my lead machine to cut my 3D meshcam gcode file without "Alarm 1- Hard...
    Thread by: cjc0306, Mar 28, 2022, 28 replies, in forum: CAM
  16. Callum McDougall
    Thread

    Thread art

    Hi everyone! My name is Callum, and I bought an ACRO 1515 machine a while back. The project I’m working on is probably quite unusual compared to...
    Thread by: Callum McDougall, Feb 20, 2022, 5 replies, in forum: Concepts and Ideas
  17. JasonNJ732
    Thread

    Connecting Optlaser to Blackbox

    I just received my Optlaser for my Lead CNC. I have it all connected except where it connects to the Blackbox. It shows in the manual connecting...
    Thread by: JasonNJ732, Jan 3, 2022, 1 replies, in forum: Laser Cutters
  18. William Holman
    Thread

    OptLaser 6w and VCarve Pro 11 on a Lead 1515

    I'm trying to create projects and so far everything looks great until I go to switch from milling to laser. I've got my drawings all done and want...
    Thread by: William Holman, Dec 17, 2021, 0 replies, in forum: CNC Mills/Routers
  19. William Holman
    Thread

    Expand Lead 1515 to 4'x8'

    Has anyone ever expanded their Lead 1515 to accommodate a full size 4x8 sheet? I just bought the 1515 and have yet to assemble. I also bought the...
    Thread by: William Holman, Dec 15, 2021, 3 replies, in forum: CNC Mills/Routers
  20. jockmac22
    Thread

    Help with Coordinate Systems

    I'm trying to determine if there is something wrong with my BlackBox controller, or just my understanding of it. I'm working with a LEAD 1515 CNC...
    Thread by: jockmac22, Oct 13, 2021, 5 replies, in forum: CNC Mills/Routers
Showing results 1 to 20 of 24
Page 1 of 2
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice