Welcome to Our Community

Some features disabled for guests. Register Today.

Sign Up

controller

Page 1 of 2
  1. Steve Jenkins
    Thread

    Blackbox controller 3D View shows phantom start/end move (green)

    I recently did a carve where I set the origin in the near the center of a hollow deep carving. Because I could not lift the bit high enough to...
    Thread by: Steve Jenkins, Oct 28, 2023, 2 replies, in forum: OpenBuilds Bug Report
  2. kajlo30
    Thread

    Laptop died

    HELLO.I used my laptop to controll my cnc with the black box controller.The SSD from the laptop is not damaged.I just wondering are the controller...
    Thread by: kajlo30, Sep 12, 2023, 3 replies, in forum: General Talk
  3. Matthew Stevens
    Thread

    Inherited Cube X printer troubles

    So I got this printer from a friend that got it from a college that was upgrading to new 3D printers. It's a 2013 model Cube X from 3D Systems. It...
    Thread by: Matthew Stevens, Jul 17, 2023, 5 replies, in forum: 3D printers
  4. Chance Houston
    Thread

    Project cutting larger than needed and machine

    Hello, super newb here. I put my machine together last week. I am using Vcarve. I get my project looking awesome in vcarve and cut my tool path....
    Thread by: Chance Houston, Oct 7, 2022, 4 replies, in forum: General Talk
  5. HarveyMatyas
    Thread

    Setting up smart phone as controller

    I was looking at docs:interface:wifi-setup [OpenBuilds Documentation] My screen does not look like this. Attached is a screen shot of my...
    Thread by: HarveyMatyas, Aug 4, 2022, 11 replies, in forum: General Talk
  6. Andy H
    Thread

    New controller set-up....

    Hi All I hope you guys can help me?! I'm just about to re-commission my OX that has been in storage for the last 4 years, and want to use the...
    Thread by: Andy H, May 30, 2022, 6 replies, in forum: Controller Boards
  7. Jakes
    Thread

    Rebuiding an OX

    Hi folks, (relatively new here - just know enough to be dangerous) I've scored what's essentially an OpenBuilds OX. It's functional, but needs a...
    Thread by: Jakes, Mar 14, 2022, 6 replies, in forum: CNC Mills/Routers
  8. dwhamm0249
    Thread

    CNC xPro V5 vs Black BOX controller

    I am looking at either the Black Box controller offered on this site or the CNC xPRO V5 that will be coming out soon. Looking into the...
    Thread by: dwhamm0249, May 5, 2021, 0 replies, in forum: Controller Boards
  9. Logan Blankenship
    Thread

    Project Starting Outside of XYZ Zero - XYZ Probe

    Hey Everyone, I finally got my lead 1515 machine up and running and wanted to run a quick test to check the tramming of my router. I mocked up a...
    Thread by: Logan Blankenship, Mar 3, 2021, 2 replies, in forum: CNC Mills/Routers
  10. Tom Lindley
    Thread

    Connect BlackBox controller to Hybrid-Step Servo?

    I have a larger servo with a HSC86H hybrid step-servo. Is it possible to hook this controller to the BlackBox? I have a BlackBox on my CNC and the...
    Thread by: Tom Lindley, Feb 16, 2021, 4 replies, in forum: Controller Boards
  11. JCCD
    Thread

    Blackbox for quenbe upgrade

    Thanks in advance to all here for even reading this, and hopefully pitching in. Bottom line: Main question: What would it take to make the...
    Thread by: JCCD, Dec 21, 2020, 4 replies, in forum: Controller Boards
  12. Mech.res
    Thread

    Use Y axis as X axis

    Hey everyone! This is my first post here so sorry if this is a little rough. I have a Workbee CNC machine with a Blackbox motion controller. My...
    Thread by: Mech.res, Nov 25, 2020, 2 replies, in forum: CNC Mills/Routers
  13. Srđan Marković
    Project

    Beginner Case For Cnc Controller (previous Build)

    Posted by: Srđan Marković, Jul 27, 2020 in category: Workshop
  14. ian_rsa
    Thread

    Help with custom Probe macro

    Hi All I run a custom build CNC with BalckboxV1.0.237. Help will be appreciated as I am stuck on an issue - I'm new to gcode, grbl and CNC'ing...
    Thread by: ian_rsa, Jun 11, 2020, 9 replies, in forum: Control Software
  15. LukePrints
    Thread

    NEMA 17 Toolhead -- how to control

    First time putting together a CNC machine, got all my parts from OpenBuilds and have a quick question, any advice or googling instructions...
    Thread by: LukePrints, Jan 18, 2020, 25 replies, in forum: General Talk
  16. ajg
    Thread

    Good 3D Printer Controller? [First Time Builder]

    Hi there, I am working on my very first 3D printer build! I'm pretty excited, but also lack a lot of knowledge in the area. My build is going to...
    Thread by: ajg, Oct 7, 2019, 1 replies, in forum: Controller Boards
  17. gdenicolas
    Thread

    Controller recommendation for C-Beam XL

    I built my C-Beam XL with a Novusun NVUM 4 Axis, but I only could use it with a Windows XP Laptop and Mach 3 software. What do you recommend me to...
    Thread by: gdenicolas, Sep 23, 2019, 9 replies, in forum: Controller Boards
  18. Recron
    Thread

    Blackbox magical axis movement

    Hello all, I'm having a dilemma. Finally I finished my C beam build and just hooked up all the wiring to the blackbox controller. All the axis...
    Thread by: Recron, Sep 7, 2019, 14 replies, in forum: Controller Boards
  19. joetemus
    Thread

    Best controller board that allows me to use Torch height control? (THC)

    Starting into the research phase of building a CNC plasma cutter. Would really like to get torch height control and I have seen some controllers...
    Thread by: joetemus, Sep 1, 2019, 1 replies, in forum: Laser Cutters
  20. Jayman
    Thread

    More than 5 axis controller

    I'm looking to add a few more axis' to a CNC machine. Is there an easy way to do this, such as a daugter board? I'm using ramps 1.4, and 2...
    Thread by: Jayman, Aug 4, 2018, 13 replies, in forum: Controller Boards
Showing results 1 to 20 of 33
Page 1 of 2
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice