Welcome to Our Community

Some features disabled for guests. Register Today.

Sign Up

black box

Page 1 of 2
  1. Tony-berumen
    Thread

    USB Problems

    I am finally getting to connect the Openbuilds Blackbox I purchased in early May, 2021. All seemed to work fine for a couple of days, then I...
    Thread by: Tony-berumen, Sep 13, 2021, 3 replies, in forum: CNC Mills/Routers
  2. Johnny Reich
    Thread

    Refubishing ProLight Turning Center and Mill

    My first post. I just took ownership of two Intelitek machine tools from a local high school that decided to decommission them. - ProLight...
    Thread by: Johnny Reich, Aug 28, 2021, 0 replies, in forum: CNC Mills/Routers
  3. Lars Plovmann
    Thread

    Making laser ingraver

    Hii all. Im a brand new member off your Fora :) Im from Denmark, and have a laser, Dremel CNC and some Prusa 3d printers. Now i make a new...
    Thread by: Lars Plovmann, Jul 14, 2021, 4 replies, in forum: Laser Cutters
  4. JayMcD
    Thread

    CNC Control Station designs?

    I am looking for some ideas for a control station build. I have custom CBeam Machine with the RoutER11 that I have built - 500mm x 1000mm...
    Thread by: JayMcD, Jun 29, 2021, 3 replies, in forum: General Electronics
  5. Tbear1123
    Thread

    Blackbox USB connection issues

    Hello, I’ve had my black box for about 2 years now with no issues. used it Monday night and Tuesday it now won’t connect via USB.. like it...
    Thread by: Tbear1123, Feb 19, 2021, 5 replies, in forum: General Talk
  6. kevinbaileycrum
    Thread

    Where to find Brain & Muscle Board Schematics

    Many moons ago I would stumble accross a link in the open builds site (whether it was forums, store, or doc I dont remember) that showed the...
    Thread by: kevinbaileycrum, Feb 2, 2021, 1 replies, in forum: Controller Boards
  7. jda70az
    Thread

    GRBL Error 2 when using X Y Z Probe Plus and Interface.

    Hi I am running a Black Box, Open Builds Interface and the XYZ Probe Plus. I Home the machine and it works as it should work, No problems...
    Thread by: jda70az, Jan 30, 2021, 10 replies, in forum: Interfaces
  8. Jacob Koeberlein
    Thread

    DM556 Drivers with Black Box

    The Black Box was recommended to me by a friend as an alternative to my current DM556 & Arduino setup that stops/disconnects randomly. I hooked up...
    Thread by: Jacob Koeberlein, Jan 18, 2021, 3 replies, in forum: CNC Mills/Routers
  9. jda70az
    Thread

    Question about Open Builds Interface and Xtension limit switches.

    I got my Lead 1010 up and running using a Black Box and the new Open Build's Interface. jogging to trigger all 3 limit switches shows the red...
    Thread by: jda70az, Jan 9, 2021, 4 replies, in forum: Other Builds
  10. Lauren85
    Thread

    Usage and Care of Power Supply

    Hello all, Currently, I leave the power supply on at all times, along with the black box. Is this a big fail on my part, or can these items be...
    Thread by: Lauren85, Jan 7, 2021, 1 replies, in forum: General Electronics
  11. JCCD
    Thread

    Blackbox for SPAM upgrade

    Thanks in advance to all here for even reading this, and hopefully pitching in. Bottom line: Main question: What would it take to make the...
    Thread by: JCCD, Dec 21, 2020, 4 replies, in forum: Controller Boards
  12. kevinbaileycrum
    Thread

    Black Box: Know what axis hit limit switch?

    Is there a way to know what axis a limit switch? When sending gcode over serial if i hit a limit switch, I want to know what axis (or rather...
    Thread by: kevinbaileycrum, Nov 17, 2020, 3 replies, in forum: Controller Boards
  13. kevinbaileycrum
    Thread

    Black Box Power supply switch ambiguity in docs

    In the power supply section of the docs for the black box it states: "Before connecting your power supply to mains power, it is critical that you...
    Thread by: kevinbaileycrum, Nov 12, 2020, 3 replies, in forum: Controller Boards
  14. CurieOS
    Thread

    BlackBox 0-10v outputting ~24v

    For some reason the 0-10v output is basically outputting VIN. I opened the top, and it kinda looked like one of the op amps is popped, but it...
    Thread by: CurieOS, Aug 19, 2020, 2 replies, in forum: Controller Boards
  15. Tommaso Seresini
    Thread

    Nema 17 grinds but doesn't rotate

    Dear all, I have set up a 2 axis rig with two paired stepper motors for the Y-axis and an isolated motor for the X-Axis. all of them are driven by...
    Thread by: Tommaso Seresini, Aug 18, 2020, 6 replies, in forum: Motors
  16. Stacey Miller
    Thread

    Can not get my stepper motors to run

    I have a WorkBee from China (Bulkman3d) and it is assembled. My Stepper motors have never worked, I thought it may be the software I was...
    Thread by: Stacey Miller, Aug 12, 2020, 2 replies, in forum: General Talk
  17. Nomad1
    Thread

    Setting a custom machine

    I am a newbie and just purchased the black box bundle and would like to know how to set up the parameters of my machine in the software.. my...
    Thread by: Nomad1, Jul 30, 2020, 5 replies, in forum: CNC Mills/Routers
  18. flysolo206
    Thread

    Blackbox - Slave the X and Z Axis?

    Thinking of a new 2 axis build. It would require 4 actuators - 2 for each axis. The Blackbox makes it easy to slave one axis (using Y and Y2...
    Thread by: flysolo206, Jul 19, 2020, 3 replies, in forum: Controller Boards
  19. BismarckDon
    Thread

    Need some help - New build

    I just completed a C-Beam machine build per the YouTube instructional videos. Got to the point of downloading and installing the OpenBuilds...
    Thread by: BismarckDon, Jul 8, 2020, 1 replies, in forum: CNC Mills/Routers
  20. RipMill
    Thread

    New Workbee. Starting to get hang of it!

    Finally got my workbee 1010 up and running. Building it was an experience. So glad I got BlackBox and xtension wires. Other than different color...
    Thread by: RipMill, May 2, 2020, 4 replies, in forum: CNC Projects
Showing results 1 to 20 of 29
Page 1 of 2
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice