Welcome to Our Community

Some features disabled for guests. Register Today.

Samson

Discussion in '3D printers' started by runninfarmer, May 30, 2015.

  1. runninfarmer

    runninfarmer Well-Known
    Builder

    Joined:
    Feb 22, 2015
    Messages:
    99
    Likes Received:
    48
    Here's a pic of the finished test print. Layers looked good, but could tell I was under extruding. Need to work on that but overall pretty happy with it.
    image.jpeg
     
    Mark Carew likes this.
  2. runninfarmer

    runninfarmer Well-Known
    Builder

    Joined:
    Feb 22, 2015
    Messages:
    99
    Likes Received:
    48
    Well, having some issues with my z-axis. My steps/mm is calculated to be 2072 and wroks well on total z-height, since I home to the max endstop. Problem is my prints are undersized, 9.2 mm for 10 mm print, 18.8 mm for 20 mm print, etc. Mechanicals seem to be fine. Have an extra geared stepper I might swap with to see if I get same result. I may go from three screws to two screws to lessen the friction load and tension.

    I'm finding a few extruder jams occasionally leading to ground filament. Not a lot but enough to make me consider switching to direct drive. Not really aiming for high speed but would be nice.
     
  3. runninfarmer

    runninfarmer Well-Known
    Builder

    Joined:
    Feb 22, 2015
    Messages:
    99
    Likes Received:
    48
    Decided to try out a large print, Julia Vase from Thingiverse. Turned out pretty well, finishing up now. Here's a pic and video:

    image.jpeg

     
  4. bob123

    bob123 New
    Builder

    Joined:
    Jul 4, 2016
    Messages:
    25
    Likes Received:
    2
    now that your build is mostly finished, would it be possible to get some details on it? Like bed size, how thick that plate is, extrusion length, the pulley types/idlers/belt ect used. I think ive decided to go with this build but i might make a few modifications to save money, im guessing those pulleys on the lead screws are pretty expensive
     
  5. runninfarmer

    runninfarmer Well-Known
    Builder

    Joined:
    Feb 22, 2015
    Messages:
    99
    Likes Received:
    48
    Hi Bob, thanks for your interest! One mod I put on that I haven't added yet is a direct drive extruder. I found out I couldn't drive the filament with my bowden setup; tube was too long and too many bends. I will post a video of the direct drive setup soon. I also have most of a BOM put together with prices and suppliers. I'll try to get that uploaded within a couple days.
     
  6. runninfarmer

    runninfarmer Well-Known
    Builder

    Joined:
    Feb 22, 2015
    Messages:
    99
    Likes Received:
    48
    Sorry for the wait, still working on the BOM and specs. Taking longer than I thought due to all the iterations I went through. Trying to get everything up to date. I'll try to get it posted soon.
     
  7. runninfarmer

    runninfarmer Well-Known
    Builder

    Joined:
    Feb 22, 2015
    Messages:
    99
    Likes Received:
    48
    Here is my current spreadsheet on expenses and various dimensions/specs. Please note this is subject to change. If you have any questions let me know. I will upload all my design files for the plates so you can have the option to 3D print the plates or use the patterns for drilling and/or CNCing.
     

    Attached Files:

  8. runninfarmer

    runninfarmer Well-Known
    Builder

    Joined:
    Feb 22, 2015
    Messages:
    99
    Likes Received:
    48
    Been a while since I posted on this and I made a couple small updates. Ran my extruder wires through one of the columns and also added a new direct drive MK8 extruder:
    IMG_0685.JPG IMG_0687.JPG
     
  9. runninfarmer

    runninfarmer Well-Known
    Builder

    Joined:
    Feb 22, 2015
    Messages:
    99
    Likes Received:
    48
    Having some problems with layers, looks like inconsistent extrusion or is it something with my z-axis? Any ideas? Here's a pic:
    IMG_0701.JPG
     
  10. bob123

    bob123 New
    Builder

    Joined:
    Jul 4, 2016
    Messages:
    25
    Likes Received:
    2
    maybe the hotend cools down because extruding to fast, then the different temps cause it to come out quick then slow, ect? try printing at slower speeds or mess with the hotend temp?
     
  11. runninfarmer

    runninfarmer Well-Known
    Builder

    Joined:
    Feb 22, 2015
    Messages:
    99
    Likes Received:
    48
    Hi Bob, thanks for the tips. Been away for work, so I've been unable to experiment yet. I'll try some different speeds and temps this weekend.
     
  12. bob123

    bob123 New
    Builder

    Joined:
    Jul 4, 2016
    Messages:
    25
    Likes Received:
    2
    another thing i thought of was maybe the temp probe in the hotend can't sense the temp fast enough. These are all just guesses tho, i still havn't built my printer yet, finally ordered most of the stuff i needed to finish it. So im sure ill be running into all these problems soon, so let me know what you find out
     
  13. crystaldragon141

    Builder

    Joined:
    Oct 27, 2016
    Messages:
    8
    Likes Received:
    10
    Judging from the fact that the pattern is repeating I'd bet it's a Z-axis problem.
     
  14. Licensed2hench

    Builder

    Joined:
    Mar 16, 2015
    Messages:
    4
    Likes Received:
    2
    Have you seen this article? It may address why the height of the whole print is slightly off.
    TrueUp Glide
    To sum up, you pick a layer height that is a multiple of a single Z motor step to prevent small positioning errors on each layer height.

    As far as the banding goes it looks really regular. But with the way the walls pulling inward it looks like it might be cyclically under extruding instead of a Z axis issue? I was having a very similar problem. For me, it was an issue with drag on the filament spool.

    I just had the spool hanging on pvc pipe. As it fed it would slowly tighten on the spool. Taking more and more pressure to feed, causing it to under extrude. Then the spool would finally slip and turn, loosening the filament for a short time, then repeat.
    Switching to a filament holder that used bearings fixed this issue.
     
    #44 Licensed2hench, Dec 13, 2016
    Last edited: Dec 14, 2016
  15. runninfarmer

    runninfarmer Well-Known
    Builder

    Joined:
    Feb 22, 2015
    Messages:
    99
    Likes Received:
    48
    Hi Licensed2hench,

    I had wondered the same. I've tried filament holders before on bearings and sometimes had them spinning too much, causing knots. Would be good to try one again, I have some extra 608's. Really hoping it would be that, because I'm scratching my head on the z-axis on where the problem is. I have noticed that the print head will drag quite a bit, even after calibrating the extruder and height. I'll check out the link to the guide you posted and give it a go. Sorry been slow on responding, I need to get Samson running again.
     
  16. bob123

    bob123 New
    Builder

    Joined:
    Jul 4, 2016
    Messages:
    25
    Likes Received:
    2
    i almost have my version of this complete, i did things a tad different as i didn't want to have to cut anything, lost a little space doing it that way but not a big deal. I have my acme rods, 2 of them, on one side as ive seen in other builds before, and it looks like the opposite side hangs about 1/4th of an inch lower :( . going to try and tighten my wheels up and hope that fix's it, i really dont understand how it could be lower the vslot should be straight and not bend.

    anyways as i started to think about the electrical part of this build i had a question. on these power supplies, isn't it highly dangerous to just wire a cord up to the screws, i mean u essentially have 120v just sitting there to be touched, and its like that on almost every build ive seen that uses these power supplies. is there any way to set that up, that isn't a huge electrical risk?

    ive also seen 3 prong plugs with a switch on them, basically like a computer power supply where u can push the cord in and out, anyone know what those things are called? i imagine they have a fuse built in too, i thought for starters that would be a good thing to get but i have no idea what they are called to even search for them. in otherwords i have a pc cord, i just need the little box with the plug and switch on it. otherwise i might just use a light switch from the hardware store, same thing i guess basically except i might be missing out on a fuse

    also of note, this vslot stuff is such a pain, i keep realizing i should have put more T nuts in and have to keep tearing the thing apart. and the brackets to hold it together twist because the holes in them are so big, so its hard to get the vslot aligned with other vslot :( . my motor mounts that hold the acme screws, they flex when i turn the screws....hoping thats not going to be an issue. oh and the build plate doesn't even have holes that match the heat bed, that might actually be the most annoying issue ive had so far. Sorry to rant but little things like this can save other people alot of time. and my hotend mount doesn't match any holes on the gantrys, that one i expected, but still not sure how to fix it without a printer, maybe some wood? anyways, ill post pictures on what i come up with
     
    #46 bob123, Dec 15, 2016
    Last edited: Dec 15, 2016
    runninfarmer likes this.
  17. bob123

    bob123 New
    Builder

    Joined:
    Jul 4, 2016
    Messages:
    25
    Likes Received:
    2
    thx, i read a few reviews and read something interesting, if the plug is rated for 15a, but the switch is 10A, isn't that bad? Most house wall plugs are 15 to 20 A, so won't this thing fry? i read a review on amazon about one of the switches melting?

    Also isn't a 250v fuse kind of pointless? shouldn't the fuse be closer to 120v? obviously not 120, or it will go off, but 250 seems like all my electronics would be fried by time it hit that
     
  18. Licensed2hench

    Builder

    Joined:
    Mar 16, 2015
    Messages:
    4
    Likes Received:
    2
    The amperage (A) switch or socket will see is what is rated to flowing through it, not what /could/ be sent to it.
    Does that make sense?

    Lets say you have a 30A breaker - feeding to 15A Sockets. This is because it is assumed you won't be pulling the full 30A through one socket. That 30A is intended to be distributed over several sockets. And the 10A switch is intended to feed to a lower amperage device.

    Example: Lets say you have 5 devices, each pulling 5A each
    Socket #1 has 2 devices. That is 5A+5A = 10A total. Still safe for Socket #1
    Socket #2 has 2 devices. That is 5A+5A = 10A total. Still safe for Socket #2
    Socket #3 has 1 device. That is 5A total. Still safe for Socket #3
    And the breaker feeding them all has 5A+5A+5A+5A+5A = 25A total. Still safe for that breaker (and wires in the walls).

    And an Example of how not to do it:
    Lets say you use a bunch of extension cords to plug EVERYTHING into one socket.
    So that 5A+5A+5A+5A+5A = 25A total is running through one socket. This does not exceed the max amperage for the breaker so it is ok, but it is exceeding the max amperage of the socket (and possibly the wires in the walls). Resulting in a potentially dangerous overload. (This is how older incandescent Christmas lights caused fires). This is why all power strips have their own breakers, so they can't be used to overload a single socket

    Keep in mind 15A is a lot. If you look on the info sticker on your device it will tell you how much power it uses, but this is usually in Watts:
    Watts = Voltage x Amps
    Amps = Watts / Voltage
    (and usually calculated assuming 110v service. The actual voltage running in you house varies depending on a lot of issues, for the math part I just go with whatever is listed on the label.)
    So a 40 Watt power supply:
    40 = A x 110
    A = 0.36A

    Or a 300 Watt power supply:
    300 = A x 110
    A = 2.73A

    So your 10A (1,100 Watts) switch should be more than strong enough to handle it.

    I hope that was helpful :)

    Fuses pop at the rated Amperage regardless of the voltage (so you can safely use a higher rated V without effecting performance). I think you see the 250v fuses so that the switch assembly can be used with a 110v or 220v setup.
     
    #48 Licensed2hench, Dec 16, 2016
    Last edited: Dec 16, 2016
    Rick 2.0 likes this.
  19. bob123

    bob123 New
    Builder

    Joined:
    Jul 4, 2016
    Messages:
    25
    Likes Received:
    2
    hmm, think ill do that cover without the switch on it, that should add pretty decent protection, still going to do that switch/plug from earlier tho incase someone trips on the cord, then it will just pull out and nothing can get shocked or fire started.

    so im at the point of needing to do my belts on the top of the machine, and i tried googling but its an odd question i have. So long question made short, how straight do my belts need to be? Eyeballing what im thinking of doing, looks like my belts will have to go at an angle to hit the pulleys. will that cause any issues?
     
  20. runninfarmer

    runninfarmer Well-Known
    Builder

    Joined:
    Feb 22, 2015
    Messages:
    99
    Likes Received:
    48
    Sorry for late reply, had to travel for work again between the holidays, and my email didn't notify me of these posts. For the pulleys, you should be able to stack them at the ends on top of the V-slot in the holes and then run the belts to the XY carrigage. The pulleys will be offset on the X Vslot carriage, but the belts themselves shouldn't connect at angles. If you do it like the original CoreXY, the belts are at angles with non-stacked pulleys, but that shouldn't matter since the X and Y forces are balanced I believe.
     
  21. runninfarmer

    runninfarmer Well-Known
    Builder

    Joined:
    Feb 22, 2015
    Messages:
    99
    Likes Received:
    48
    Samson has officially evolved and now has a belt driven z-axis utilizing a 5:1 geared nema17 stepper driving two separate belts. The z-axis total weight is roughly 10 lbs so this stepper has nowhere near enough torque to lift it. I've overcame that using 65 lbs test spectra line and two 5 lb iron plates on each side. It's not the prettiest yet, but it's temporary while I test the axis. Works really smooth and I'm pretty pleased with it so far. Haven't printed anything but have done some movement tests. Here are some pics:
    IMG_0771[1].JPG
    IMG_0772[1].JPG
    IMG_0773[1].JPG
     
  22. runninfarmer

    runninfarmer Well-Known
    Builder

    Joined:
    Feb 22, 2015
    Messages:
    99
    Likes Received:
    48
    Here's a video of the movement tests:
     
  23. Shortyski13

    Builder

    Joined:
    Mar 28, 2017
    Messages:
    40
    Likes Received:
    10
    How well does your heated bed work with those wires? I'm designing a project very very similar to yours and was thinking of doing that.
     
  24. runninfarmer

    runninfarmer Well-Known
    Builder

    Joined:
    Feb 22, 2015
    Messages:
    99
    Likes Received:
    48
    Hi Shortyski13, works great! People are hesitant to use 120V/240V mains for heated beds, but it eliminates the need for additional power supply. You can also get a higher wattage heater tape. Mine's ~ 600 W and heat's up pretty quick. Just have to be very careful with wiring and keeping connections enclosed. I recently trimmed this aluminum build plate down for my Kool Bot build and I anticipate the new size (16" x 16" x 1/8") should heat up in under 5 mins or less.
     
  25. Shortyski13

    Builder

    Joined:
    Mar 28, 2017
    Messages:
    40
    Likes Received:
    10
    Holy quick response time, Batman! Thanks! I may have to go this route. My build is actually a bit bigger, looks like about 18" x 24" build area with slightly larger bed. I don't mind slower heating up times though. My problem is that I don't know much about how to wire something like that, other than snaking the heating wires under the heat bed. Could you shed some light (if/when you have time) on how you connect it to your controller board (if you do at all) to control the heat, and how you hooked it up to plug into i'm guessing the wall (I'm at 110v)? Sadly electronics is not my forte but I'm trying to learn all I can with this, and I certainly am!
     
  26. runninfarmer

    runninfarmer Well-Known
    Builder

    Joined:
    Feb 22, 2015
    Messages:
    99
    Likes Received:
    48
    No problem. I will preface that main power AC is dangerous so exercise caution. I just used a power cord, cut off the female plug and hooked up the wires according to diagram below. You can get a 30A - 50A solid state relay (SSR) pretty cheap on ebay ($5-$15) but you have to be careful because I've heard that a lot of these cheap ones are counterfeit and can cause fires. I haven't had any problems with the cheap one I got, but if you want to be safe you can spend more on a brand that's trustworthy. I use the output off my RAMPs D08 output to control the SSR. In typical setups this output runs a smaller heated bed, such as MK2, etc. Here I'm just using the output signals to control the SSR on/off. The SSR is just an electrical signal driven switch. I always add a mechanical switch into the 120V line to the SSR so I can always kill power to the bed if I need to, without needing to unplug the cord.

    Heated bed diagram.jpg
     
  27. Shortyski13

    Builder

    Joined:
    Mar 28, 2017
    Messages:
    40
    Likes Received:
    10
    What made you decide to "upgrade" to belt driven z-axis? I'm trying to make this decision now and like the precision of lead screws, but i know they can potentially have z-wobble problems.
     
  28. runninfarmer

    runninfarmer Well-Known
    Builder

    Joined:
    Feb 22, 2015
    Messages:
    99
    Likes Received:
    48
    I hadn't really liked the screw design I had. Screws work, just wasn't the best design. I like the simplicity and cost of belts. One thing I've learned is getting proper tension with belts on z-axis can be difficult.
     

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice