Chris Laidlaw

Hi Chris, I am in the UK and making a build that looks like the OX & Piranha style build. I am after a full set of plates - my machine is based on a 1000mmx1000mm with HGR20 rails C Beam Extrusion 80mmx40mm & Block ball screw Rm1605-1000mm
It looks like your 9" Sphinx kit may well work, but not sure if US extrusion is the same as that in the uk?

Also, would all of your threads and screws be in imperial?

Hey Chris, my name is Thirry and we talked over on eBay. I was wondering what your price would be for a version of the Sphinx CNC 4 Y end Plate set, but with specs for using the 1605 ball screws rather than the 8mm rods?

chrisclub@gmail.com

Hi chris...This is Scott.

Hi Chris this is Joe

Hi Chris, I contacted you via ebay about the custom plates. I'll contact you at your gmail. Thanks

Sending you a request.

sending a message as requested. Erik

You can reach me at chrisclub@gmail.com for any custom parts you may need. I ship world wide. Thanks :)

Hi Chris - considering converting my Platemaker build to Sphinx. Kyo indicated he is not quite ready to ship his plates, but indicated that you could make them. I just found your ebay listings and see that you have them in stock.

Are these v1 or v2? If v1, would there be a change in price to mill a v2 set?

Thanks for your reply,

Mark

Hi Chris was just on to you on ebay (Gary) I would be using the same makita as you have in pic
thanks gary

Does anyone make the ooznest ox plate kit in the US? I can order it from the UK with a two week delay. Thanks

Chris, we spoke on Ebay. I'm looking for a price on having the Joe's CNC Evo part milled/shipped to 40047, KY.

Hi Chris We talked on EBAY. I am building a large laser cut table. Any parts you have that will help my build I am interested in. Since this is a Laser cuter I am trying to make the Gantry light.
Link to my build
http://www.openbuilds.com/builds/large-laser-cut-table-build.2806/

Good morning Chris, i looking to up grade my So2 OX ZILLA 36' x 36' work area and about 4" Z .... what are you plate z dimensions

Hi Chris, This is DJ and I messaged you earlier. I see your gmail and I'm not sure how to PM, so I'll write you via your email. Thanks for the super speedy reply! All the best!

4 Wheel Spacer Blocks 15 5-Hole Joiners 20 Router Mount 85 Dust Collector 80 Magnetic Dust Collector 120 International shipping 50

chrisclub@gmail.com

chrisclub@gmail.com

chrisclub@gmail.com

chrisclub@gmail.com

hello
Just sent you a message on Ebay.....
My name is nivush...
my email is nivzuzut@hotmail.com

Hey Chris,

Just sent you a message on Ebay. I need some advice on building an Ox :)

I am at chrisclub@gmail.com

You see this is why I like one point for all conversation, you spend all of your life checking different locations.

single point - Email. -hamitduk@gmail.com

Hi,

I requested info on Ebay a bit ago.

I am not one for forms, do you have a Email address so we can trade info?

Chris,

Just checking to see if you know how I can start a conversation with you as requested?

Shawn

Chris,

Sorry I just figured out how to start a new conversation after I posted the message below to you. However, when I tried to click "Start New Conversation", I received an error stating I couldn't start a conversation specifically with you. Do you know what I'm doing wrong? Do you have to invite me or do I have to follow you first?

Shawn

Chris,
...from eBay to here.

In your opinion, is the OX suitable to do small scale production work in hardwood and alum? If you don't mind me asking, what machine are you using to create your alum OX gantry plates? I'm new to CNC and trying to figure out how to build a stout enough machine to produce quality hardwood and alum milling.

Any suggestions?
Thanks,
Shawn

Looking for OX gantry plates you got I need :) in big ole Texas...