David the swarfer's Recent Activity
-
David the swarfer replied to the thread OpenBuild Accro 1015 plotting inconstancy.
that pattern is mesmerizing
May 7, 2024 at 2:44 AM -
David the swarfer liked targz's post in the thread OpenBuild Accro 1015 plotting inconstancy.
So I finally figured it out, I had some play in my X motor pulley, It were invisible to me before I found a way to lock the motor....
May 7, 2024 at 2:44 AM
-
David the swarfer liked Oleks Lytv's post in the thread multifunctional CNC machine.
This is right. Combining a CNC mill, laser device, and 3D printer can create conflicts in terms of speed, power, and accuracy, as each...
May 7, 2024 at 2:44 AM -
David the swarfer replied to the thread New build and first cut odd issue..
you MUST home the machine, either with the homing limit switches and press the Home button in CONTROL before setting up to cut, or by...
May 6, 2024 at 10:00 AM -
David the swarfer liked Peter Van Der Walt's post in the thread H100 VFD 220V with 1.5Kw Spindel 2 poles air cooled with Black Box.
Just takes 3 things. Set $30 to whatever your spindles actual max RPM is Set tool rpm in your Toolpath Make sure to use our Fusion...
May 6, 2024 at 4:34 AM -
David the swarfer replied to the thread Design Software.
on the other hand I am absolutely sure which postprocessor is better for plasma, our Openbuilds post is the one (-: The stock one is not...
May 6, 2024 at 4:32 AM -
David the swarfer liked Alain JBT's post in the thread New to OpenBuilds.
Hi, In this category of linear machine and architecture the only limit I know would be 1540 mm. (Lead Screws) for maximal travel...
May 6, 2024 at 3:52 AM -
David the swarfer replied to the thread multifunctional CNC machine.
in general this is a bad idea CNC cutting needs relatively slow speeds and *power* to drive the tool through the material laser/3D...
May 6, 2024 at 3:51 AM -
David the swarfer liked Peter Van Der Walt's post in the thread Openbuilds CAM/Openbuilds Control/JD garage plasma table.
Normally not needed, when you add the toolpath it pops up the same window. You mustve Cancelled that window without doing the setup, for...
May 2, 2024 at 10:51 AM
-
David the swarfer replied to the thread Problems with openbuilds control, ubuntu, Mega2560 and Grbl-mega-5x.
Linux is not the problem, the Mega256 is the problem, CONTROL is designed to work with *stock* GRBL 1.1 on an Arduino Uno (as in the...
May 2, 2024 at 10:50 AM -
David the swarfer liked Misterg's post in the thread G1 adaptive clearing slow feedrate.
Post up a screenshot of the 'Tool', 'Passes' and 'Linking' tabs on the Fusion360 settings for the operation and I'll take a look. (Make...
May 1, 2024 at 4:50 AM -
David the swarfer liked EvanH's post in the thread RoutER11 died?.
Hi Bill, It is worth checking in the CNC cookbook feeds and speeds what also happens when the machine cuts at full width (as in...
May 1, 2024 at 4:48 AM -
David the swarfer liked EvanH's post in the thread RoutER11 died?.
Yes 3 angular bearings are quite a common configuration and would be fine. There are a few spindles out there specifically for...
May 1, 2024 at 4:47 AM -
David the swarfer liked Peter Van Der Walt's post in the thread Switching from Arduino running GRBL to BB X32 running GRBLHAL.
Enter $$=22 for example into the Serial Terminal, grblhal will output the Help for that command [ATTACH] (TIP: Only 1 and 0 is...
Apr 30, 2024
-
David the swarfer replied to the thread RoutER11 died?.
this is a community forum. if you wanted support for the Router11 from the store then you should have contacted the store (-: also,...
Apr 30, 2024