Welcome to Our Community

Some features disabled for guests. Register Today.

Sign Up

Search Results

Search Again
Page 1 of 2
  1. Tajudeen
    Post

    OpenBuilds CONTROL Software

    From unresolved error now to broken z limit switche. Could someone show me how to use the Workbee cnc router without the limit switches?
    Post by: Tajudeen, Nov 17, 2019 in forum: Control Software
  2. Tajudeen
    Post

    OpenBuilds CONTROL Software

    Thank you for your reply I increased pull off to 25mm. Nothing changed.
    Post by: Tajudeen, Nov 17, 2019 in forum: Control Software
  3. Tajudeen
    Post

    OpenBuilds CONTROL Software

    No it is the same error I have been getting all this while. This same setup works perfectly prior to relocating the Workbee. What shall I do now?
    Post by: Tajudeen, Nov 13, 2019 in forum: Control Software
  4. Tajudeen
    Post

    OpenBuilds CONTROL Software

    i Ensured the limit switches wiring is in the above order. And I continue to get this error as the z axis moves passed the limit swithch. The...
    Post by: Tajudeen, Nov 12, 2019 in forum: Control Software
  5. Tajudeen
    Post

    OpenBuilds CONTROL Software

    @Alex Chambers Please is there a way to manually home my cnc router? This will be a good alternative to my none functioning limit switches
    Post by: Tajudeen, Nov 7, 2019 in forum: Control Software
  6. Tajudeen
    Post

    OpenBuilds CONTROL Software

    @Peter Van Der Walt ,@Alex Chambers please can you take a look for me now? [14:50:42] [ 3D Viewer ] WebGL Support found! success: this application...
    Post by: Tajudeen, Nov 7, 2019 in forum: Control Software
  7. Tajudeen
    Post

    OpenBuilds CONTROL Software

    I Thank you for your message. I will check out how to do that and post accordingly. UOTE="Alex Chambers, post: 88830, member: 123072"]Hi...
    Post by: Tajudeen, Nov 4, 2019 in forum: Control Software
  8. Tajudeen
    Post

    OpenBuilds CONTROL Software

    Thank you @Alex Chambers I have wired all switches in similar order. But Will check to make sure.
    Post by: Tajudeen, Nov 4, 2019 in forum: Control Software
  9. Tajudeen
    Post

    OpenBuilds CONTROL Software

    Post by: Tajudeen, Nov 4, 2019 in forum: Control Software
  10. Tajudeen
    Post

    OpenBuilds CONTROL Software

    Thank you for your response. I was looking for away to run the cnc router without the limit switches. Invert Y stepper on grbl settings resolved this.
    Post by: Tajudeen, Nov 4, 2019 in forum: Control Software
  11. Tajudeen
    Post

    OpenBuilds CONTROL Software

    Please if the limit switches will not work, How do I setup work with out those? I have tried several times but the y axis keeps straying off work.
    Post by: Tajudeen, Nov 4, 2019 in forum: Control Software
  12. Tajudeen
    Post

    OpenBuilds CONTROL Software

    Thank you for your observation. What shall I set the probe pin to please?
    Post by: Tajudeen, Nov 4, 2019 in forum: Control Software
  13. Tajudeen
    Post

    OpenBuilds CONTROL Software

    Thank you for your response. I have changed the homing debounce rate to 250 and the wiring moved as you suggested. Upon homing afterwards, thaz...
    Post by: Tajudeen, Nov 3, 2019 in forum: Control Software
  14. Tajudeen
    Post

    OpenBuilds CONTROL Software

    I Thank you for response. I have changed the homing debounce to 250 and moved the wire as advised. Upon homing, the z axis moved past the switch...
    Post by: Tajudeen, Nov 3, 2019 in forum: Control Software
  15. Tajudeen
    Post

    OpenBuilds CONTROL Software

    Thank you for your reply. I uploaded the requested file
    Post by: Tajudeen, Nov 3, 2019 in forum: Control Software
  16. Tajudeen
    Post

    OpenBuilds CONTROL Software

    [ATTACH]
    Post by: Tajudeen, Nov 3, 2019 in forum: Control Software
  17. Tajudeen
    Post

    OpenBuilds CONTROL Software

    @Skip S. Please share your resolve. I cannot route any job because of same issue
    Post by: Tajudeen, Nov 3, 2019 in forum: Control Software
  18. Tajudeen
    Post

    OpenBuilds CONTROL Software

    HI, thank you for your post. I have been challenged by the same issue for up to 4 days after moving my workbee to a new location. Could please...
    Post by: Tajudeen, Nov 3, 2019 in forum: Control Software
  19. Tajudeen
    Post

    Limit switches false alarm

    Thank you for your help. I have resolved using the settings link
    Post by: Tajudeen, Oct 24, 2019 in forum: General Electronics
  20. Tajudeen
    Post

    Limit switches false alarm

    Thank you for the info
    Post by: Tajudeen, Oct 24, 2019 in forum: General Electronics
Showing results 1 to 20 of 35 Next >
Search Again
Page 1 of 2
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice