Welcome to Our Community

Some features disabled for guests. Register Today.

Sign Up

Search Results

Search Again
Page 1 of 2
  1. Armadillo Works
    Post

    I want to design and build a small engraver/cutter with a limited knowledge

    My K40 CO2 only worked well after I got rid of the M2 Nano controller and China software. Replaced the unit with a controller I could use...
    Post by: Armadillo Works, Mar 29, 2021 in forum: Laser Cutters
  2. Armadillo Works
    Post

    40W CO2 Laser Controlled by Eleksmaker Mana SE

    Great! The xPro and the Blackbox boards are a lot more versatile than some of the lighter boards on the market which require more support...
    Post by: Armadillo Works, Mar 8, 2019 in forum: Laser Cutters
  3. Armadillo Works
    Post

    40W CO2 Laser Controlled by Eleksmaker Mana SE

    This WIKI link will explain what a MOSFET is. MOSFET - Wikipedia Generally it is just a solid state voltage/current regulating device.
    Post by: Armadillo Works, Mar 7, 2019 in forum: Laser Cutters
  4. Armadillo Works
    Post

    Workbee 1010

    [ATTACH] Well the WorkBee will carve wood! Ran the Hello World test print and all went well. I needed to use a smaller bit but 1/4" is...
    Post by: Armadillo Works, Mar 4, 2019 in forum: CNC Mills/Routers
  5. Armadillo Works
    Post

    Workbee 1010

    The Workbee is up and running! Need to make a few changes before I start making wood chips.
    Post by: Armadillo Works, Mar 3, 2019 in forum: CNC Mills/Routers
  6. Armadillo Works
    Post

    Workbee 1010

    Thanks! Gary. As with anything new it is always good to ask questions. By your avatar I assume you are into RC aircraft. So am I and my last...
    Post by: Armadillo Works, Mar 3, 2019 in forum: CNC Mills/Routers
  7. Armadillo Works
    Post

    Workbee 1010

    I finally have the mechanical portion of the Workbee assembled and am working on the electronics this morning. [ATTACH] I have connected...
    Post by: Armadillo Works, Mar 3, 2019 in forum: CNC Mills/Routers
  8. Armadillo Works
    Post

    K40 12x24in rebuild (In Original Case)

    I have one of each and they all have their issues. Laser you will have to deal with smoke or fumes. Rotary you are going to have to deal with dust...
    Post by: Armadillo Works, Feb 26, 2019 in forum: Laser Cutters
  9. Armadillo Works
    Post

    Workbee 1010

    Thanks! Mary. o_O Confusion cleared up. :thumbsup:
    Post by: Armadillo Works, Feb 25, 2019 in forum: CNC Mills/Routers
  10. Armadillo Works
    Post

    Workbee 1010

    Mary, The steppers that I received; three (3) that are labeled 2303HS280AW-OB and one (1) 2315HS300AW-OB. All four steppers are 83 mm in length....
    Post by: Armadillo Works, Feb 25, 2019 in forum: CNC Mills/Routers
  11. Armadillo Works
    Post

    Workbee 1010

    The length of all four of the steppers is 3-1/4" (83mm) which is bigger that the standard Nema 23 on the parts store site. I really would like...
    Post by: Armadillo Works, Feb 25, 2019 in forum: CNC Mills/Routers
  12. Armadillo Works
    Post

    Workbee 1010

    Good to know on the current but wasn't sure if having various torque ratings would pose a problem. I removed the higher amp one since I had...
    Post by: Armadillo Works, Feb 25, 2019 in forum: CNC Mills/Routers
  13. Armadillo Works
    Post

    Workbee 1010

    Getting closer! I have a question that came up while installing my NEMA 23 High Torque steppers which I ordered 4 of. After unpacking them and...
    Post by: Armadillo Works, Feb 25, 2019 in forum: CNC Mills/Routers
  14. Armadillo Works
    Post

    Workbee 1010

    The build is up to Step 20 in the video. Took a little time to get it squared up. Planning on adjusting eccentrics and installing lead screws...
    Post by: Armadillo Works, Feb 23, 2019 in forum: CNC Mills/Routers
  15. Armadillo Works
    Post

    Workbee 1010

    Just got back in! Alex it was the Open Builds Parts Store in NJ. Roger
    Post by: Armadillo Works, Feb 22, 2019 in forum: CNC Mills/Routers
  16. Armadillo Works
    Post

    Workbee 1010

    I figured as much. Problem is the remaining 15mm low profile screws are needed to complete the base frame. They are used for attaching the...
    Post by: Armadillo Works, Feb 22, 2019 in forum: CNC Mills/Routers
  17. Armadillo Works
    Post

    Workbee 1010

    [ATTACH] [ATTACH] I am down to Step 17 on my Workbe 1010 and have found a potential problem. The last instructions of the step is to install the...
    Post by: Armadillo Works, Feb 21, 2019 in forum: CNC Mills/Routers
  18. Armadillo Works
    Post

    Workbee 1010

    I just finished up on Step 11 of the video - Mounting Z-Axis plate to X-Axis plate. It is starting to look like a machine as opposed to a pile...
    Post by: Armadillo Works, Feb 20, 2019 in forum: CNC Mills/Routers
  19. Armadillo Works
    Post

    Workbee 1010

    Thanks! I have been busy getting her assembled.
    Post by: Armadillo Works, Feb 20, 2019 in forum: CNC Mills/Routers
  20. Armadillo Works
    Post

    Workbee 1010

    I figured it was needed but wanted to make sure. Thanks!
    Post by: Armadillo Works, Feb 20, 2019 in forum: CNC Mills/Routers
Showing results 1 to 20 of 30 Next >
Search Again
Page 1 of 2
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice