Recent Activity
Activity stream for all registered members at OpenBuilds.
-
David the swarfer replied to the thread URGENT HELP NEEDED.
plastics don't like climb milling, foamed plastics even less so.... I posted about this, with pictures recently.... OpenBuilds Sketchup...
May 9, 2024 at 10:33 AM -
David the swarfer liked dJOS_500's post in the thread MKS DLC 32 problem..
Unfortunately it’s useless on everything but the stock firmware. TBH I think it’s kinda useless anyway. I got so annoyed with its...
May 9, 2024 at 10:26 AM -
David the swarfer liked kth's post in the thread multifunctional CNC machine.
This sounds very similar to the Snapmaker 3-n-1 concept, it is a "jack of all trades master of none". It ends up an expensive limited...
May 9, 2024 at 10:24 AM -
David the swarfer replied to the thread Laser Tree Diode Module.
the BlackBox has 2 outputs for laser power 5v PWM 0-10V DC which one does that control board need? connect that one (-:
May 9, 2024 at 6:52 AM -
Safetywrench liked Peter Van Der Walt's post in the thread Reading values from OpenBuilds Control software.
Oh and just to reply to this section: Yes, seperate app that would be better. Allows it to function separately. But do use socket.io -...
May 9, 2024 at 1:21 AM -
Rick 2.0 replied to the thread Wall Mounted ACRO Exploration.
This is a bit of a difficult one to make suggestions on based on the size. You’ll definitely want the X-axis set vertically as the only...
May 8, 2024 at 4:13 PM -
Tim Schmidt attached a file to the thread OpenBuilds CONTROL v1.0.375 Finds wrong IP Address.
Notes: All Software and Firmware updated as of yesterday (CONTROL, x32, and INTERFACE). Network Strength Full Bars [ATTACH]
May 8, 2024 at 12:14 PM -
Tim Schmidt replied to the thread OpenBuilds CONTROL v1.0.375 Finds wrong IP Address.
Thank You for the response. I had to reconfigure my network for a 2.4GHz network; my 5GHz network SSID is one letter off and I grabbed...
May 8, 2024 at 11:25 AM -
JustinTime liked Peter Van Der Walt's post in the thread Aftermarket tool height setter.
It is a SpoilBoard. Not a "i want to keep $5 worth or MDF pristine for life"-board lol. Its a consumable (;
May 8, 2024 at 9:54 AM -
David the swarfer replied to the thread Aftermarket tool height setter.
[MEDIA]
May 8, 2024 at 6:20 AM -
David the swarfer liked Peter Van Der Walt's post in the thread Aftermarket tool height setter.
It is a SpoilBoard. Not a "i want to keep $5 worth or MDF pristine for life"-board lol. Its a consumable (;
May 8, 2024 at 6:19 AM -
David the swarfer replied to the thread Stream G-Code from Home Shop.
no, 4 miles is too far, and as Peter said, never leave the machien unattended.
May 8, 2024 at 2:38 AM -
David the swarfer liked Peter Van Der Walt's post in the thread Stream G-Code from Home Shop.
Add an Interface to the CNC machine: docs:interface:start [OpenBuilds Documentation] so you don't need a PC there. 4 miles is far too...
May 8, 2024 at 2:37 AM -
Tim Schmidt posted a new thread.
OpenBuilds CONTROL v1.0.375 Finds wrong IP Address
Press Scan and Open Builds finds a controller 192.168.0.129 and stops. The controller was turned OFF; same results. The Controller is...
Forum: Control Software
May 7, 2024 at 10:18 PM -
Giarc replied to the thread Rotating the dxf x&y axis.
If using Vectric products, highlight the .dxf file then press either the 9 or 0 button. that will rotate it 45degrees each press if I...
May 7, 2024 at 4:27 PM