Welcome to Our Community

Some features disabled for guests. Register Today.

1250x1000 Build

Discussion in 'Laser Cutters' started by jnsbanman, Jan 9, 2020.

  1. jnsbanman

    jnsbanman Well-Known
    Builder

    Joined:
    Dec 15, 2015
    Messages:
    46
    Likes Received:
    28
    jnsbanman published a new build:

    Read more about this build...
     
  2. jnsbanman

    jnsbanman Well-Known
    Builder

    Joined:
    Dec 15, 2015
    Messages:
    46
    Likes Received:
    28
    Got the bed frame made and the knife bed installed today. Still waiting on interior panels to be cut so I can start mounting electronics.
     

    Attached Files:

  3. jnsbanman

    jnsbanman Well-Known
    Builder

    Joined:
    Dec 15, 2015
    Messages:
    46
    Likes Received:
    28
    Here is some more of my progress from this weekend.
    - Interior panels on
    - Wiring run to the steppers and end stops
    - Drivers, controller and power supply added

    I should have some motion test this week I hope.
     

    Attached Files:

  4. Jaybyrd42

    Jaybyrd42 New
    Builder

    Joined:
    Jul 13, 2015
    Messages:
    2
    Likes Received:
    0
    Loving the build! I'm in the process of sourcing parts for my build but I'm having trouble finding a bed large enough (1500x1500), where did you order yours from?
     
  5. jnsbanman

    jnsbanman Well-Known
    Builder

    Joined:
    Dec 15, 2015
    Messages:
    46
    Likes Received:
    28
    Check out Will Feng Store on AliExpress. He can custom size one for you. Very reasonable pricing too. Tell him Jason Banman sent you
     
    Jaybyrd42 likes this.
  6. jnsbanman

    jnsbanman Well-Known
    Builder

    Joined:
    Dec 15, 2015
    Messages:
    46
    Likes Received:
    28
    First Moves... check tube and tube power supply next up.
     

    Attached Files:

  7. James Babcock

    Builder

    Joined:
    Feb 2, 2020
    Messages:
    3
    Likes Received:
    0
    Is this a cloudray linear actuator setup?
     
  8. James Babcock

    Builder

    Joined:
    Feb 2, 2020
    Messages:
    3
    Likes Received:
    0
    I would like to know where you sourced your knife bed parts from? If you don't mind sharing.

    Jim.
     
  9. jnsbanman

    jnsbanman Well-Known
    Builder

    Joined:
    Dec 15, 2015
    Messages:
    46
    Likes Received:
    28
    Go to Will Feng Store on AliExpress... Tell him Jason Banman sent you
     
  10. jnsbanman

    jnsbanman Well-Known
    Builder

    Joined:
    Dec 15, 2015
    Messages:
    46
    Likes Received:
    28
    Got the water system running yesterday, hope to get the air assist running today and get a test burn in. Wait on exterior panels to be cut, and still have to build the lid.
     
  11. James Babcock

    Builder

    Joined:
    Feb 2, 2020
    Messages:
    3
    Likes Received:
    0
    Thanks for the info. I does not look like they offer them directly. Can I assume you had to contact them? I see that the linear actuator kits from Feng and Cloudray are virtually identical. Looks like Will Feng is cheaper though. I wonder who is actually making them. My setup is stuck on hold until China gets moving again.

    Jim.
     
  12. jnsbanman

    jnsbanman Well-Known
    Builder

    Joined:
    Dec 15, 2015
    Messages:
    46
    Likes Received:
    28
    Yes I have had him make that bed custom, he is making me a custom laser tube as well. He custom sized my X/Y stage as well. He is responsive on chat, and has fairly good english
     

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice