Welcome to Our Community

Some features disabled for guests. Register Today.

The New "Smoothieboard" controller

Discussion in 'Controller Boards' started by bobt, Dec 28, 2013.

  1. bobt

    bobt Well-Known
    Builder

    Joined:
    Dec 4, 2013
    Messages:
    89
    Likes Received:
    38
    I have just received my new "Smoothieboard" controller.
    002-1.jpg 003-1.jpg 004-1.jpg 005-1.jpg 006-1.jpg 007-1.jpg

    There is the first initial shots of the board. Now to get down to work and hook this up to the Shapeoko machine that I am going to use as a 3D printer.

    Bob
     
    Robert Hummel likes this.
  2. bobt

    bobt Well-Known
    Builder

    Joined:
    Dec 4, 2013
    Messages:
    89
    Likes Received:
    38
    Ok - did I get mine before you did Mark??

    Bob
     
  3. Mark Carew

    Mark Carew OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jun 28, 2013
    Messages:
    2,742
    Likes Received:
    2,407
    :D not sure Bob, I do have mine but have not had the chance to try it out as of yet. I have a ton of projects on the table now, but I do have plans for this one.
     
  4. The Dude

    The Dude Well-Known
    Builder

    Joined:
    Jan 2, 2014
    Messages:
    243
    Likes Received:
    102
    hey can the smoothie run a routy or OX which has been refitted with a multi-head spindle+plastruder+laser+picker+plotter+dragknife+??? without reloading the firmware? I realize there would need to be some extra gcodes added to tell it which head to use. An example might be a 3D printed circuit board that then has parts placed on it and then laser etched labeling, all in one run or maybe just stopping for a tool change.
     
  5. Mark Carew

    Mark Carew OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jun 28, 2013
    Messages:
    2,742
    Likes Received:
    2,407
    That's the hope :) I think the concept behind this board is great but it does still keep us in the NEMA 17 realm of things.
     
  6. bobt

    bobt Well-Known
    Builder

    Joined:
    Dec 4, 2013
    Messages:
    89
    Likes Received:
    38
    Only if you use the onboard drivers. There are break out connections to attach any other type of drivers to it.
    Also any of these operations are possible because all the code can be loaded. But that was not the original intent of the design. The original intent is to allow the controller to be used for any of these types of operations but one at a time. But you could do all of them it is just simple matter of programming (SMOP).

    Bob
     
  7. The Dude

    The Dude Well-Known
    Builder

    Joined:
    Jan 2, 2014
    Messages:
    243
    Likes Received:
    102
    what would be a good breakout board for running a nema23 off the smoothieboard? What are those things anyway? Like 10A?
     
  8. Mark Carew

    Mark Carew OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jun 28, 2013
    Messages:
    2,742
    Likes Received:
    2,407
    With this you could wire up most any of them out there like geckos for instance.
    http://www.geckodrive.com/geckodrive-step-motor-drives.html
     
  9. The Dude

    The Dude Well-Known
    Builder

    Joined:
    Jan 2, 2014
    Messages:
    243
    Likes Received:
    102
  10. Mark Carew

    Mark Carew OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jun 28, 2013
    Messages:
    2,742
    Likes Received:
    2,407
    Public Do Omens likes this.
  11. The Dude

    The Dude Well-Known
    Builder

    Joined:
    Jan 2, 2014
    Messages:
    243
    Likes Received:
    102
    #11 The Dude, Jan 14, 2014
    Last edited: Jan 14, 2014
  12. Mark Carew

    Mark Carew OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jun 28, 2013
    Messages:
    2,742
    Likes Received:
    2,407
    I guess if you dig in you could, not sure about how to go about that though. I am just thinking hooking up this drivers may be a quick easy way to drive higher amp bigger steppers.
    :D
     
  13. Public Do Omens

    Guest Builder

  14. The Dude

    The Dude Well-Known
    Builder

    Joined:
    Jan 2, 2014
    Messages:
    243
    Likes Received:
    102
  15. Public Do Omens

    Guest Builder

    What we need is to know what will drive what when and how.
    If we can find and consolidate all this information for all to share then this would help spread OPEN knowledge.

    This knowledge should not be profiteered from, like shop owners want.

    566 oz lift one inch from shaft now that is powerful!

    :cool: Times are hard lets share more FREE.
     
  16. bobt

    bobt Well-Known
    Builder

    Joined:
    Dec 4, 2013
    Messages:
    89
    Likes Received:
    38
  17. Tweakie

    Tweakie OpenBuilds Team
    Moderator

    Joined:
    Jan 18, 2014
    Messages:
    784
    Likes Received:
    326
    Excellent info Bob, thanks for posting the link :thumbsup:

    Tweakie.
     
  18. Craig & Silas

    Builder

    Joined:
    Oct 11, 2016
    Messages:
    29
    Likes Received:
    6
    This looks very well done, have you completed the one for the CNC Machine?
     
  19. Rick 2.0

    Rick 2.0 OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Dec 20, 2013
    Messages:
    2,855
    Likes Received:
    1,525
  20. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    13,754
    Likes Received:
    4,070
    These days, there's also a nice alternative:
    Instead of using Smoothieware (which is more of a 3D printing firmware) you can install Grbl-LPC : cprezzi/grbl-LPC - massively fast, works great and as its Grbl, works with all the more standard Grbl supported CNC toolchains, post processors, CAM, CONTROL, etc softwares
     
  21. Craig & Silas

    Builder

    Joined:
    Oct 11, 2016
    Messages:
    29
    Likes Received:
    6
  22. Craig & Silas

    Builder

    Joined:
    Oct 11, 2016
    Messages:
    29
    Likes Received:
    6
    Peter
    I have already purchased the Smoothie board as part of the C-Beam XL bundle, as I understand it should work with CAM and CONTROL. Is that true? Being new to this I do not know enough to understand the differences between the two boards.

    Craig
     
  23. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    13,754
    Likes Received:
    4,070
    Yes, if you install Grbl LPC as mentioned above onto it.

    Smoothieware / Grbl = firmwares
    Smoothieboard = the PCB
    Good to know the difference :)

    You can install GrblLPC onto the Smoothieboard.
     

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice