Welcome to Our Community

Some features disabled for guests. Register Today.

Sign Up

Brand new black box

Discussion in 'Controller Boards' started by Chadfarmer, Jun 3, 2019.

Page 2 of 2
  1. NthAxisWorkshop

    NthAxisWorkshop New
    Builder

    Joined:
    Apr 11, 2018
    Messages:
    55
    Likes Received:
    24
    - Alex, you beat me to it. :)
    If I understand correctly, the stepper wiring / current has been resolved and now limit switches are the issue? To wire "plain jane" switches to the Blackbox : "c" (common) goes to GND and "no" (normaly open) goes to SIG. Wire "nc" to SIG if you run your switches for break sense. If using Xtension switches GND to GND, V+(LED) to V+, SIG to SIG. Not rocket science, kiddo. As Alex said, wire color not really important except for keeping your connections straight. I think the Xtension wires use BLACK,RED, BLUE color scheme. Switches broke..from the PCB? From the solder terminals?
     
    #31 NthAxisWorkshop, Jun 9, 2019
    Peter Van Der Walt likes this.
  2. sharmstr

    sharmstr OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 23, 2018
    Messages:
    2,035
    Likes Received:
    1,431
    He indicated on the FB page that it ended up being a loose wire.
     
    #32 sharmstr, Jun 9, 2019
  3. NthAxisWorkshop

    NthAxisWorkshop New
    Builder

    Joined:
    Apr 11, 2018
    Messages:
    55
    Likes Received:
    24
    Ah. The infamous FB. Didn't realize these were being mitigated there as well. Noted.
     
    #33 NthAxisWorkshop, Jun 9, 2019
  4. sharmstr

    sharmstr OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 23, 2018
    Messages:
    2,035
    Likes Received:
    1,431
    I try to send support issues over here. Its much easier here than FB. But everyone has their preference I suppose.
     
    #34 sharmstr, Jun 9, 2019
  5. Chadfarmer

    Chadfarmer New
    Builder

    Joined:
    Feb 13, 2019
    Messages:
    99
    Likes Received:
    1
    Got it all going doing opposite of the diagram lol go figure.
     
    #35 Chadfarmer, Jun 9, 2019
  6. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    13,997
    Likes Received:
    4,109
    Did you notice the text above the image?

    See the TIP section.
    Screenshot_2019-06-09-20-17-24-785_com.android.chrome.png
     
    #36 Peter Van Der Walt, Jun 9, 2019
  7. Sully3535

    Sully3535 New
    Builder

    Joined:
    May 30, 2019
    Messages:
    25
    Likes Received:
    1
    I am having the same problem. Won't connect.
     
    #37 Sully3535, Jun 15, 2019
  8. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    13,997
    Likes Received:
    4,109
    Follow the advise above, step by step, and advise.

    Disconnect everything
    Just plug in USB
    Make sure you have FTDI Drivers installed

     
    #38 Peter Van Der Walt, Jun 15, 2019
  9. Sully3535

    Sully3535 New
    Builder

    Joined:
    May 30, 2019
    Messages:
    25
    Likes Received:
    1
    OB Display.png
     
    #39 Sully3535, Jun 15, 2019
  10. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    13,997
    Likes Received:
    4,109
    Thanks for the screenshot but no mention of the rest?

    - Wiring mistakes can prevent the board from booting properly
    - incorrect FTDI Drivers can cause USB issues: Virtual COM Port Drivers
     
    #40 Peter Van Der Walt, Jun 16, 2019
  11. Sully3535

    Sully3535 New
    Builder

    Joined:
    May 30, 2019
    Messages:
    25
    Likes Received:
    1
    I tried all of that. Tried a different computer as well. Same issue.
     
    #41 Sully3535, Jun 18, 2019
    Thomas C Kelly likes this.
  12. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    13,997
    Likes Received:
    4,109
    Have you tried reflashing from Tools and Wizards -> Grbl Flashing on the toolbar at the top?
     
    #42 Peter Van Der Walt, Jun 18, 2019
  13. Sully3535

    Sully3535 New
    Builder

    Joined:
    May 30, 2019
    Messages:
    25
    Likes Received:
    1
    Yes. I can see a red light on the controller flash when I do that. But after that still no connection.
     
    #43 Sully3535, Jun 18, 2019
  14. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    13,997
    Likes Received:
    4,109
    Does it succeed or fail (on the Serial terminal)

    :) The more details the quicker we can get to the bottom of it.
     
    #44 Peter Van Der Walt, Jun 18, 2019
  15. Sully3535

    Sully3535 New
    Builder

    Joined:
    May 30, 2019
    Messages:
    25
    Likes Received:
    1
    I don't know what that means. It was working fine until the fan quit. I have made no changes to the controller or my computer.
     
    #45 Sully3535, Jun 18, 2019
  16. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    13,997
    Likes Received:
    4,109
    #46 Peter Van Der Walt, Jun 18, 2019
  17. Sully3535

    Sully3535 New
    Builder

    Joined:
    May 30, 2019
    Messages:
    25
    Likes Received:
    1
    Thanks. I have been in contact with them already.
     
    #47 Sully3535, Jun 18, 2019
  18. Sully3535

    Sully3535 New
    Builder

    Joined:
    May 30, 2019
    Messages:
    25
    Likes Received:
    1
    Flash failed
     
    #48 Sully3535, Jun 18, 2019
Page 2 of 2

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice