Welcome to Our Community

Some features disabled for guests. Register Today.

very, very, very new to the CNC world.

Discussion in 'CNC Mills/Routers' started by Kevin Bruner, Jun 29, 2018.

  1. Kevin Bruner

    Builder

    Joined:
    Aug 29, 2014
    Messages:
    55
    Likes Received:
    9
    settings. i wasnt able to get back to this screen until i restored it to GRBL. meaning when i would click on "get GRBL settings" button, nothing would happen.
     

    Attached Files:

  2. Giarc

    Giarc OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jan 24, 2015
    Messages:
    2,898
    Likes Received:
    1,613
    What made you choose 26.667 for your $100 and $101? Because that is nearly a factor of 10 low for an 8 mm pitch screw at 1/8 microstepping.

    Also, it looks like you built the Sphinx which has a geared down z axis, so 200 for your $102 Is most likely wrong. If it is a 1 to 1 gear, tben 200 is the starting point. If I were you, I would request the proper settings for that model, then calibrate it so it is precise. Maybe the settings were provided in the manual or the build video? Either way, the formulas to figure it out on your own were in the GRBL wiki page. I posted the $ settings openbuilds provided for the Cbeam earlier. It uses the same openbuilds lead screws. If you used lead screws from elsewhere, then you will have even more homework to do tracking the screw characteristics down.
     
    #32 Giarc, Jul 22, 2018
    Last edited: Jul 22, 2018
  3. Kevin Bruner

    Builder

    Joined:
    Aug 29, 2014
    Messages:
    55
    Likes Received:
    9
    I got it back to where I could pull the settings and then adjust them. When I would hit G0 x100 it would go to the right. I adjusted it and got it close then it started going to the left withthat command. Do I have to shut it down and restart it between adjustments?
     
  4. Kevin Bruner

    Builder

    Joined:
    Aug 29, 2014
    Messages:
    55
    Likes Received:
    9
    Also on $100 I want to say that was a default setting. I had gone back and set it to 200.000 as a starting point.
     
  5. Kevin Bruner

    Builder

    Joined:
    Aug 29, 2014
    Messages:
    55
    Likes Received:
    9
    The gears on the z-axis are both 20 tooth so it’s a 1:1. Right? I don’t want to sound like an *** at all. I really do appreciate the help. I know I sound a bit whiny and all and for that I apologize.
     
  6. Kevin Bruner

    Builder

    Joined:
    Aug 29, 2014
    Messages:
    55
    Likes Received:
    9
    I was having some binding on the z-axis and I tried to gap the pulley from the plate to help. Well, I ripped the threads out trying to tighten it back up. So I guess once parts come in I will give it another shot.
     

    Attached Files:

  7. Rick 2.0

    Rick 2.0 OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Dec 20, 2013
    Messages:
    2,852
    Likes Received:
    1,524
    Yes.
    Don't worry about it. We all understand frustration. As long as you're doing all you can to work through the problem, we're here to help.
     
    Giarc, GrayUK and Kevin Bruner like this.
  8. Giarc

    Giarc OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jan 24, 2015
    Messages:
    2,898
    Likes Received:
    1,613
    You should not have to shut it down. One of the things with Grbl Panel, and other senders, is if your spindle is at x150 (or anything greater than the 100) and you say G0 x100 it will go to the left until it hits the x100 mark, so in this example 50 mm.

    It is good to hear things were moving the right direction for you.
     
  9. Kevin Bruner

    Builder

    Joined:
    Aug 29, 2014
    Messages:
    55
    Likes Received:
    9
    so, while i am waiting on parts to arrive i was playing around with sketchup and sketchucam. i have noticed that my "tool path" always looks the same. a big red square of zigzag lines. isn't it supposed to look like the picture or thing i am wanting to cut out?
     

    Attached Files:

  10. Kevin Bruner

    Builder

    Joined:
    Aug 29, 2014
    Messages:
    55
    Likes Received:
    9
    new pulley should be here today. looking at "paid" software, will the vcarve work with this xpro v3 board i have? it looks like it is in inches and not mm.
     
  11. Giarc

    Giarc OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jan 24, 2015
    Messages:
    2,898
    Likes Received:
    1,613
    I am not sure why you get this. When I drew up something similar, it looked like it should. There is a great manual for sketchucam if you click the "?" tab.

    As for Vcarve, you should be able to use mm. I think we are one of the few countries that has not been smart enough to convert to the much easier format of metric. If they only used inches, they would eliminate about 6.7 billion potential sales. ;)
     
    Kevin Bruner likes this.
  12. Kevin Bruner

    Builder

    Joined:
    Aug 29, 2014
    Messages:
    55
    Likes Received:
    9
    Not the best pictures but I got the new pulley on and installed the limit switches. Need to wire them up next. Playing with the free trial of vcarve right now.
     

    Attached Files:

  13. Kevin Bruner

    Builder

    Joined:
    Aug 29, 2014
    Messages:
    55
    Likes Received:
    9
    i believe i will be getting the vcarve program as it has been the easiest for me to get to work, may be the trial program that is easy but i like the way it is laid out. anyways, i bought some cable organizers from the parts store on here, how do they mount? i mean as far as brackets, is it something i have to make or is there something already out there to mount them with?
     
  14. Gary Caruso

    Gary Caruso OpenBuilds Volunteer
    Staff Member Moderator Builder

    Joined:
    May 19, 2016
    Messages:
    1,184
    Likes Received:
    531
    Hi Kevin, Are you talking about drag chain?
    Lots of ways to mount, most people use some home made bracket, I was able to use some cut offs of 2040 for mounting them.
    Combination of angle brackets and 2040 or even just some plastic brackets will work.
    Regards
    Gary
     
  15. Kevin Bruner

    Builder

    Joined:
    Aug 29, 2014
    Messages:
    55
    Likes Received:
    9
    Ok. I was looking at it last night and was thinking I had assembled it wrong. Lol. I will toy around with it when I get off tonight.
     
  16. Kevin Bruner

    Builder

    Joined:
    Aug 29, 2014
    Messages:
    55
    Likes Received:
    9
    And yes, I was talking about the drag chain.
     
  17. GrayUK

    GrayUK Openbuilds Team Elder
    Staff Member Moderator Builder

    Joined:
    May 5, 2014
    Messages:
    1,668
    Likes Received:
    627
    Of Course!! :D:D
    Ah, those were the days. :banghead:
     
  18. Grimace

    Grimace New
    Builder

    Joined:
    Aug 12, 2018
    Messages:
    41
    Likes Received:
    18
    @kevinbruner
    @andreasbockert

    We are very new here ourselves and I am glad I saw this thread as I have a feeling this info will definitely come in handy!
     
    Kevin Bruner likes this.
  19. Kevin Bruner

    Builder

    Joined:
    Aug 29, 2014
    Messages:
    55
    Likes Received:
    9

    i made my first "test" sign from the trial version of vcarve this weekend. didn't set the bit right so i stopped it. machine is still in the house so i don't want to make a huge mess.
     

    Attached Files:

  20. Grimace

    Grimace New
    Builder

    Joined:
    Aug 12, 2018
    Messages:
    41
    Likes Received:
    18
    @kevinbruner

    You did a great job! I think we will need to try the trial version too. I was looking at it before, but the machine isn't quite finished yet, so I am holding off on it. I feel rather intimidated, but am so excited at the same time.
     
    Kevin Bruner likes this.

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice