Welcome to Our Community

Some features disabled for guests. Register Today.

C-Beam Sphinx with a twist

Discussion in 'CNC Mills/Routers' started by SamKircher, Aug 9, 2017.

  1. SamKircher

    Builder

    Joined:
    Sep 12, 2016
    Messages:
    23
    Likes Received:
    12
    SamKircher published a new build:

    Read more about this build...
     
  2. MaryD

    MaryD OpenBuilds Team

    Joined:
    Apr 13, 2016
    Messages:
    649
    Likes Received:
    639
    Following :)
     
  3. Mark Carew

    Mark Carew OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jun 28, 2013
    Messages:
    2,742
    Likes Received:
    2,407
    Never to young to build! Awesome to see you have some help:thumbsup: have fun
     
  4. SamKircher

    Builder

    Joined:
    Sep 12, 2016
    Messages:
    23
    Likes Received:
    12
    Thanks guys!

    So I have been trying all day to get bCNC to just connect to the phoenix control board with no luck. It just doesn't show up in the com ports at all, even though the computer is showing it is connected in device manager.

    Very confused and have no idea what I am doing, any help would be great.
     
  5. cmwwebfx

    cmwwebfx New
    Builder

    Joined:
    Dec 2, 2017
    Messages:
    62
    Likes Received:
    5
    Good looking build. Do you think it is sufficient to build the Sphynx out of MDF as a start to then be able to cut our own alloy plates from a machine built with MDF?
     
  6. SamKircher

    Builder

    Joined:
    Sep 12, 2016
    Messages:
    23
    Likes Received:
    12
    I probably wouldn't go straight to aluminum from mdf. Its just not stiff enough.
     
    cmwwebfx likes this.
  7. cmwwebfx

    cmwwebfx New
    Builder

    Joined:
    Dec 2, 2017
    Messages:
    62
    Likes Received:
    5
    Ahh ok, I was thinking that the MDF might hold up enough to upgrade itself by cutting its own upgrade parts from alloy. Am trying to figure a way to do the aloy parts without finding someone else to do them.
     
  8. Scotty Orr

    Scotty Orr Journeyman
    Builder

    Joined:
    May 21, 2015
    Messages:
    315
    Likes Received:
    177
    If the MDF is accurate enough to properly locate the holes (or to cut a thin template material), I don't see why you couldn't do that, and finish an initial alloy set on the band saw and drill press (if you have those).
     
  9. SamKircher

    Builder

    Joined:
    Sep 12, 2016
    Messages:
    23
    Likes Received:
    12
    Second what Scotty said, use it to spot your holes etc, then drill out on the drill press, then cut none critical geometry by hand. If you are like me your final plates won't be even close to what you thought when you started, so maybe cut some test ones with your CNC out of mdf, and make your alloy ones the third set. My set right now are acrylic which is pretty stiff, but has its downsides. Looks nice though.
     
  10. GrayUK

    GrayUK Openbuilds Team Elder
    Staff Member Moderator Builder

    Joined:
    May 5, 2014
    Messages:
    1,668
    Likes Received:
    627
    I used a set of very rigid 12mm plastic chopping boards to get started. :D
    Easy to cut and make, and lasted well enough to very gently make the ali plates. :thumbsup:
     
    cmwwebfx likes this.
  11. cmwwebfx

    cmwwebfx New
    Builder

    Joined:
    Dec 2, 2017
    Messages:
    62
    Likes Received:
    5
    Genius idea.
     
  12. Hayri PhoenixCNC

    Builder

    Joined:
    Jul 23, 2017
    Messages:
    4
    Likes Received:
    1
    Hi Sam,

    This is Hayri maker of the Phoenix CNC Controller, I know this is an older post but if you still need any help please let me know.
     

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice