Welcome to Our Community

Some features disabled for guests. Register Today.

HULK-XY (Fixed Build Plate, C-Beam, CoreXY)

Discussion in '3D printers' started by Adam Filipowicz, Sep 21, 2015.

  1. Adam Filipowicz

    Adam Filipowicz Journeyman
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    259
    Likes Received:
    129
    here you go

    Frame hasnt changed in a long time.

    Good Luck with the build.
    please post photos! :)
     

    Attached Files:

    Jose A. Molina likes this.
  2. Adam Filipowicz

    Adam Filipowicz Journeyman
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    259
    Likes Received:
    129
    Video of some testing. trying to get smooth motion at 300mm/sec

     
    Mark Carew likes this.
  3. Jose A. Molina

    Jose A. Molina Well-Known
    Builder

    Joined:
    Mar 7, 2016
    Messages:
    62
    Likes Received:
    61
    That's mesmerizing. do you find the printhead wobbling at those speeds?
     
  4. Adam Filipowicz

    Adam Filipowicz Journeyman
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    259
    Likes Received:
    129
    I havent tried to actually print at this speed. I have doubts it would work.. especially with PETG,
    I will attempt it with PLA..with a thin layer height

    its very solid and doesnt wobby much. but the X gantry does have more weight then i would like since its using a full size Nema 17 Stepper and the Y has Double MGN12 Rails which gives it alot of mass.
     
  5. Jose A. Molina

    Jose A. Molina Well-Known
    Builder

    Joined:
    Mar 7, 2016
    Messages:
    62
    Likes Received:
    61
    I have only tried bowden myself but that has a lot of its own issues. could a geared nema 17 lighten the head a bit and still generate the torque needed?
     
  6. Adam Filipowicz

    Adam Filipowicz Journeyman
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    259
    Likes Received:
    129
    I am using a E3D Titan which has a 3:1 gear ratio and they use it with a Small Nema 17 (Pancake) but the one i got didnt work so i put in a full size one for now, until i get another pancake 17, they dont weigh much. Bowden is a pain in the butt.
     
  7. Jose A. Molina

    Jose A. Molina Well-Known
    Builder

    Joined:
    Mar 7, 2016
    Messages:
    62
    Likes Received:
    61
    Yeah. lol in my Boden-Ventures i've even gone as far as oil my tube to try to reduce the friction. theres lots of hang ups there.
     
  8. Adam Filipowicz

    Adam Filipowicz Journeyman
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    259
    Likes Received:
    129
    Its a very solid print head, no wobble. really prints great.
     
  9. Corbin Major

    Builder

    Joined:
    Jun 21, 2016
    Messages:
    2
    Likes Received:
    0
    I am also attempting this build. I have had the required parts lying around, as I was going to build a D-Bot, but I really wanted a fixed build plate and the ability to add an enclosure in the future, and your build just fits the bill of everything I'm looking for! Just cut everything and am starting assembly of the frame tonight. One difference is that I'm using OpenRails for the XY rails instead of the MGR rails, but other than the carriage, that doesn't seem to be of any large effect.

    I'm following your progressive updates the the a360 my hub page, though between that, the pictures and videos, and the actual stl files available I think I have it all just about figured out.

    Also, does anybody know how to get the dimensions of an object in a360? I can get volume and density, but I really want length, width and height, so that I can be sure of which screws go where etc without having to guess and test forever trying different ones out.

    Thanks for any assistance, and for putting together such an amazing build! I'll definitely post pictures as I go along and get things rolling!
     
  10. GBCues

    GBCues New
    Builder

    Joined:
    Apr 20, 2016
    Messages:
    5
    Likes Received:
    0
    "does anybody know how to get the dimensions of an object in a360" In Fusion 360, load your project, click on "Inspect" at the top, then click "Measure"
    HTH
     
  11. Corbin Major

    Builder

    Joined:
    Jun 21, 2016
    Messages:
    2
    Likes Received:
    0
    Thanks! I've got the frame almost assembled, and I'm finishing up the gantry as well. I modified the dimensions a little bit to make it larger, but that's mostly just changing the extrusion lengths, so being able to measure things in the model will be a huge help. I don't know if you guys have heard of Mechaduino, but I backed them on Kickstarter a year or so back and got my motors a few months ago, and I'm using three of my six on this build, with the idea of the closed loop being great, but the real benefit being the magnetic encoding allowing for just about unlimited resolution while maintaining speed and torque. I'll probably start with them as drop in replacements using stepper drivers, but at some point I'd like to just route the dir/step data direct and let the onboard controller sort it, which should also allow for much greater resolution as well as reporting feedback on resistance or skipped steps to the firmware so it can correct itself if it skips steps or is interfered with. The idea being that it could immediately interrupt the other motors, correct itself, then resume the print hopefully without any visible issues.
     
  12. ade2

    ade2 New
    Builder

    Joined:
    Mar 29, 2017
    Messages:
    1
    Likes Received:
    0
    Hi! This model looks super interesting. Any updates on build progress or how it's working out? Any place to find more info?
     
  13. Nanzer

    Nanzer New
    Builder

    Joined:
    Apr 27, 2017
    Messages:
    5
    Likes Received:
    0
    Hey, I'm about to start this build. Any tips?
     
  14. Adam Filipowicz

    Adam Filipowicz Journeyman
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    259
    Likes Received:
    129
    Good Luck on your Builds. cant wait to see some photos.
    Tip. use a Picture Frame clamp to make sure its nice and square.

    I havent used the machine for a few months, unfortunately. been focusing on other things.
    last time i did use it.. its super solid. compared too my previous prusa printer,
     
  15. Nanzer

    Nanzer New
    Builder

    Joined:
    Apr 27, 2017
    Messages:
    5
    Likes Received:
    0
    Thanks a lot! After reading through all the documentation etc. I couldn't figure out how your gantry works. Is it still using V Slot rails? Or is it using C Beams?
     
  16. Nanzer

    Nanzer New
    Builder

    Joined:
    Apr 27, 2017
    Messages:
    5
    Likes Received:
    0
    Also, I'm planning to use an E3D v6 with a Bowden. Do you think that would be a smart design? I don't plan to use flexible filaments
     
  17. Adam Filipowicz

    Adam Filipowicz Journeyman
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    259
    Likes Received:
    129
    I originally build it using 40x40 for the Verticals and 20x20 and 20x40 for the gantry
    Later on i ended up adding Linear ball Slides, But this wasnt necessary and did add alot of weight

    I would suggest to save yourself some frustration to go with Direct drive with A E3D Titan and V6
    in my experience Bowden is always way more work to tweak to get retraction right to reduce blobs.
     
  18. Nanzer

    Nanzer New
    Builder

    Joined:
    Apr 27, 2017
    Messages:
    5
    Likes Received:
    0
    Thanks. Since I'm ordering all my parts from China, the Titan would end up way too expensive for now. I'd love to add it, but I couldn't find any Chinese clones unfortunately.
     
  19. gogo2390

    gogo2390 New
    Builder

    Joined:
    Mar 18, 2015
    Messages:
    2
    Likes Received:
    0
    I have the titan and it works great. They just came out with a new one (titan aero) that is allinone and includes the hot end/heatsink in a more compact form factor...you don't need to have an e3dv6 hanging underneath it. Jury is still out on how good it is, but it's still an interesting thing to look into....Less dangling weight??

    Titan Aero (1.75mm 24V)
     
  20. Nanzer

    Nanzer New
    Builder

    Joined:
    Apr 27, 2017
    Messages:
    5
    Likes Received:
    0
    Can somebody elaborate on which pillow block mounts I should use?
     
  21. Adam Filipowicz

    Adam Filipowicz Journeyman
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    259
    Likes Received:
    129
    Working on a new version, trying to only use Openbuilds components.
    so far cannot be 100% openbuilds, The top belt loop is special, also the Gt2 Pulleys with 8mm Bore, and the Extruder/BL Touch

    Still just a quick rough assembly.

    Have a look here

    A360

    titan xy v2 may 28.JPG
     
  22. Kaarbble

    Kaarbble New
    Builder

    Joined:
    Oct 20, 2015
    Messages:
    13
    Likes Received:
    5
    Hello
    Already build two large bot with open build, I am curious about this D bot.

    is there d bot stl files for 2020 profiles?

    Thank you,

    mat?
     
  23. ixlix

    ixlix New
    Builder

    Joined:
    Feb 21, 2016
    Messages:
    1
    Likes Received:
    0
    Anymore updates on this? Im really interested in making a large version of the linear rail version. I tried your 360 files, but they seem to have most parts missing.
     
  24. Adam Filipowicz

    Adam Filipowicz Journeyman
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    259
    Likes Received:
    129
    been using the machine, no updates really.. not really planning on updating with new files any time soon.
    biggest issues so far have been keeping wires heading to extruder out of the way., great machine overall.
     
  25. daisosasen01

    Builder

    Joined:
    Sep 24, 2016
    Messages:
    58
    Likes Received:
    2
    Did you finish your build? How are the mechaduino's working out for you?
     
  26. Andyfilms

    Andyfilms New
    Builder

    Joined:
    Sep 6, 2018
    Messages:
    1
    Likes Received:
    0
    Thinking about building one of these! Does anyone have pics of prints they could share? Is the print quality worth the effort vs. A comparably priced off the shelf machine?

    The fixed bed is appealing for accuracy reasons.
     
  27. patnap71

    patnap71 New
    Builder

    Joined:
    Apr 18, 2018
    Messages:
    12
    Likes Received:
    2
    I would really love to see other people's builds and prints.
    Would like to make a 500x500 or 600x600 but with a belted linear railed Z on the 4 corners, linear rails on top of extrusions for XY along with a Titan Aero.
    Torn between this fixed bed corexy beauty, all metal 500mm Kossel Delta or 500mm Tevo Little Monster inspired delta.
     
    #147 patnap71, Oct 9, 2018
    Last edited: Oct 9, 2018
  28. Adam Filipowicz

    Adam Filipowicz Journeyman
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    259
    Likes Received:
    129
    I updated the summary of the this build with current info. and also uploaded fusion 360 files.
    Right now this printer is pretty printing super well.
     
  29. Emiliano Salvador

    Builder

    Joined:
    Nov 6, 2019
    Messages:
    2
    Likes Received:
    0
    hello from Argentina
    Excellent project, is this machine currently in force?
    Are there photos of the result of the unpredictability?
     
  30. Adam Filipowicz

    Adam Filipowicz Journeyman
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    259
    Likes Received:
    129
    The TitanXY is for sale. PM me if your interested
     

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice