Welcome to Our Community

Some features disabled for guests. Register Today.

Batxillerat Research Project: Design and construction of a CNC

Discussion in 'CNC Mills/Routers' started by Pol Feliu, Jul 6, 2014.

  1. Pol Feliu

    Pol Feliu New
    Builder

    Joined:
    Mar 2, 2014
    Messages:
    8
    Likes Received:
    2
    Pol Feliu published a new build:

    Read more about this build...
     
  2. Seul Kee

    Seul Kee New
    Builder

    Joined:
    Mar 10, 2014
    Messages:
    16
    Likes Received:
    1
    Hi, Pol!

    I am also a new OpenBuilder living in Busan, South Korea. (I have been to your
    city once about 10 years ago and I had a great time!)

    I just begun to work on my 4' x 4' OX-like CNC router which I hope to finish by
    the end of July. :D

    That is why I am keenly interested in your CNC build. (Especially with respect to
    your Arduino-based solution.)

    I originally wanted to use Arduino and some shields together with LinuxCNC.

    After many sleepless nights, however, I ended up choosing EdingCNC's CPU5A4
    control board and its free control software. It is awesome that you designed the
    motor control board yourself!

    Come to think of it, I should have posted my build like you and others did. But
    I must admit that I was lazy as well as busy. :nailbite: I will do sooner or later, though!

    Best luck for your CNC build!

    Tae
     
    #2 Seul Kee, Jul 6, 2014
    Last edited: Jul 6, 2014
  3. Pol Feliu

    Pol Feliu New
    Builder

    Joined:
    Mar 2, 2014
    Messages:
    8
    Likes Received:
    2
    Thankyou! I've just finished building the board, and haven't tested yet. I hope it will work!

    I was lazy about it too. Now I'm kind of stucked and i don't have much work to do because the components from the part store are taking a while...
     
  4. Mark Carew

    Mark Carew OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jun 28, 2013
    Messages:
    2,742
    Likes Received:
    2,407
    Welcome to OpenBuilds @Pol Feliu ! The work sheet that you put together looks great and we look forward to your builds :thumbsup:
    Mark
     
  5. JerryD

    JerryD New
    Builder

    Joined:
    Jun 26, 2017
    Messages:
    8
    Likes Received:
    0
    Nice Build, I'm designing something similar. Any deflection issues with the tall gantry supports?
     
  6. Pol Feliu

    Pol Feliu New
    Builder

    Joined:
    Mar 2, 2014
    Messages:
    8
    Likes Received:
    2
    Hello Jerry. I haven't done more updates on this post (haven't had the time). Since then i changed the dremel to a laminate trim router that works better but it is heavier. It is more stiff than it looks but it could be defnitly better. Long story short: if you have the money, time and resources go for a water/plasma cut plate like the OX routers, if you don't and use a small spindle/router like i do and want the flexibility to change the height of the y axis this is great.

    I've been meaning to change it but not because it doesn't work well, but rather because i would like to move on to a nice silent watercooled spindle.

    Lots of things have changed, hope i find some time to write them down.
     
  7. JerryD

    JerryD New
    Builder

    Joined:
    Jun 26, 2017
    Messages:
    8
    Likes Received:
    0
    Thanks for the insight, Pol. I'll consider the OX plates, the only issue is Z-axis travel. Most of them have minimal travel ranges of 4-6". I'm looking to get a max of 12-16" depending on how I mount the machine to the table. 90% of anything I do at that height will be soft wood etching, laser etching, or 3D printing so it's not like the machine will be under harsh forces like cutting wood or aluminum. I would like to have the ability to cut wood an aluminum if I need to and in that case I could lower the gantry to as low as practical. It's looking more like building two machines may be the best option. If I had the room for two machines that would help, lol!

    Thanks again!
    -J
     
  8. Pol Feliu

    Pol Feliu New
    Builder

    Joined:
    Mar 2, 2014
    Messages:
    8
    Likes Received:
    2
    You could make some tall plates. What i mean is that they must be worth it because its more simple since the wheels and the y gantry mount directly to it.

    If you get them custom made i suggest you make several holes so that you can adjust the height to the table if you needed. That would be very cool. With this most of the Z axis would be unused but its not a problem since you'd be using the stiffer part of it


     
  9. JerryD

    JerryD New
    Builder

    Joined:
    Jun 26, 2017
    Messages:
    8
    Likes Received:
    0
    I like that idea. I've also considered making a portion of the table and spoil board removable (open to the floor) so I could drop in tall work pieces when I need to.
     
  10. Pol Feliu

    Pol Feliu New
    Builder

    Joined:
    Mar 2, 2014
    Messages:
    8
    Likes Received:
    2
    watch frank howarth's vertical table on his old cnc video.
    Its very cool, but for jointery i still think a pantorouter is better.
     

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice