Welcome to Our Community

Some features disabled for guests. Register Today.

Z probe and bcnc set up??

Discussion in 'CNC Mills/Routers' started by pitzerwm, Oct 18, 2016.

  1. pitzerwm

    pitzerwm New
    Builder

    Joined:
    Sep 10, 2016
    Messages:
    20
    Likes Received:
    1
    I have asked this over at Github and no answers, I have read everything and watched all of the videos and I still have a question. Bcnc appears to automate the probe function. In the wiki manual, it skips right over the Probe tab, and goes to Autolevel, which at this time, I don't need.

    See pix for the blank spaces that are there to help you get the z 0 set quickly.

    I have the plate, thickness 1.61 mm and wired in to the controller board. When I place the bit over the plate a few mm it lowers, touches and stops. Obviously, this isn't really z0, where do I tell the software that the plate thickness needs to be subtracted or added depending on your point of reference?

    Thanks for any help.

    [​IMG]
     
  2. David the swarfer

    David the swarfer OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Aug 6, 2013
    Messages:
    3,239
    Likes Received:
    1,815
    What does TLO do ?
     
  3. David the swarfer

    David the swarfer OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Aug 6, 2013
    Messages:
    3,239
    Likes Received:
    1,815
    Also, on the 'tool' tab there is a 'calibrate' box, I think that is where you put in the touch plate thickness
     
    Giarc likes this.
  4. OldDogSleeping

    Builder

    Joined:
    Oct 22, 2015
    Messages:
    11
    Likes Received:
    11
    you can type values into the WPOS boxes; so once the probe has completed, enter your plate thickness as the current Z Value.

    Alternatively you could use one of the user configurable buttons on the Control Screen and set it to run something like;
    G38.2 Z-3 F1
    G92 Z1.61
     
  5. Kyo

    Kyo Veteran
    Staff Member Builder Resident Builder

    Joined:
    Feb 27, 2014
    Messages:
    673
    Likes Received:
    699
    @David the swarfer TLO is Tool Length Offset..

    A simple way would be to enter your plate thickness in tlo run your probe routine and then hit Z=0.. If you want to use probing often just set up a marco. Both options are discussed "Here"

    The Calibration option is used to find your plate thickness for tool changes vs the zero of your work. You can read about it "Here".

    I prefer the paper or feeler gauge method. Simple and quick. When I get around to trying a pcb I might have to look into probing / auto leveling more.
     
    #5 Kyo, Oct 19, 2016
    Last edited: Oct 19, 2016
    David the swarfer likes this.
  6. pitzerwm

    pitzerwm New
    Builder

    Joined:
    Sep 10, 2016
    Messages:
    20
    Likes Received:
    1
  7. wiremonkey

    Builder

    Joined:
    Mar 23, 2017
    Messages:
    40
    Likes Received:
    12
    I automate XYZ in UGS with a macro, 10 seconds, done:
    I broke down the gcode in the comments section for those that are learning, like myself.
     
    #7 wiremonkey, Jun 1, 2017
    Last edited: Jun 1, 2017
    Hisha, Mike Piechowski and Kyo like this.
  8. Thomas53

    Thomas53 New
    Builder

    Joined:
    Aug 16, 2019
    Messages:
    1
    Likes Received:
    3
    Sorry to say but I find this solution very devious . . . Give my solution a try and give me your opinion . . .
    1 take a micro switch and drill a ~3mm hole in the back . . .
    2 glue with 2comp epoxy the shaft of a broken cutter or dril in this hole . . .
    3 solder two wires to C and NO and connect them with your Probe Terminal.

    With this 50 cents tool you can Auto Level non conducting material.
    It will give you a precision/resolution better than 50 microns and also works top when you want to engrave.
    All letters and symbols will have exactly the same depth !

    Regards, Tom


    BEANTWOORDEN
     

    Attached Files:

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice