Welcome to Our Community

Some features disabled for guests. Register Today.

OX Build

Discussion in 'CNC Mills/Routers' started by adhd_nerd, Oct 1, 2014.

  1. adhd_nerd

    adhd_nerd New
    Builder

    Joined:
    Sep 27, 2014
    Messages:
    3
    Likes Received:
    8
    GrayUK likes this.
  2. Mark Carew

    Mark Carew OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jun 28, 2013
    Messages:
    2,742
    Likes Received:
    2,407
    Great looking build @adhd_nerd :thumbsup: I like the use of the angle iron.
    Where did you find that nice Estop switch?
    Keep up the good work and thank you for sharing
     
  3. jdcncjunky

    Builder

    Joined:
    Apr 27, 2014
    Messages:
    2
    Likes Received:
    2
    Awesome job, that looks amazing.
     
    joe.carson likes this.
  4. Serge E.

    Serge E. Journeyman
    Builder

    Joined:
    May 6, 2014
    Messages:
    730
    Likes Received:
    251
    Sweet looking machine ... I'm still struggling with the getting the X beams (full uncut 1500mm) squared with the Y plates.

    Looking forward to your initial tests ...
     
  5. Macchp

    Macchp New
    Builder

    Joined:
    Mar 14, 2014
    Messages:
    42
    Likes Received:
    5
    Thanks for sharing.
    Those are exactly the dimensions I was looking at for a "potential" build of an OX to work on full sheets of DEPRON (80X125cm).

    How big is her working area?

    Looking forward to your progress ready to steal some good hint :thumbsup:
     
  6. Serge E.

    Serge E. Journeyman
    Builder

    Joined:
    May 6, 2014
    Messages:
    730
    Likes Received:
    251
    The working areas is about 52" wide (X) by only about 19" deep (Y) once everything is done. But I can work 'infiite' Y by doing sections, once I figure out a good way to align sections (slide the work piece through). I have a few ideas to try out when the time comes ... Could of went with 1000 mm lengths for the Y axis, but that would of made for a huge OX. I might be able to gain a few inches once I test out some ideas for the X/Z assembly ... there's a lot of overhang (cantilever ?), thus potential twisting force on the X beam.

    The one thing to watch out for, which I'm having trouble with right now, is to make X square with Y ... there's 1500mm (actually: 1503), slightest 'error' at one end becomes huge at the other end. At this time, I'm down to the last 17.5 mm (difference from one end to other). No matter what I do, I can't seem to get any better ... it's getting on my nerves, especially after rebuilding most of the machine 3 times.

    There's a growing number of large builds going on, at least one is looking at splicing two lengths to reach 6' working length (in Y axis). So we'll see how who gets an handle on precision over extended lengths soon enough.
     
  7. adhd_nerd

    adhd_nerd New
    Builder

    Joined:
    Sep 27, 2014
    Messages:
    3
    Likes Received:
    8
    Estop came from amazon.
     
    Mark Carew likes this.

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice