Welcome to Our Community

Some features disabled for guests. Register Today.

Cbeam not cutting smooth when transversing x and y axis

Discussion in 'CNC Mills/Routers' started by phoenix fab, Aug 12, 2019.

  1. sharmstr

    sharmstr OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 23, 2018
    Messages:
    2,030
    Likes Received:
    1,428
    For sure. I've only done the Y beams and there's a noticeable difference in cut quality between X and Y. After doing the Y, I measured the flex in the Y beams before and after adding the supports. Before it was .017", now its .002". The X beam will get 2 rails since I cant add supports.
     
  2. Alex Chambers

    Alex Chambers Master
    Moderator Builder

    Joined:
    Nov 1, 2018
    Messages:
    2,681
    Likes Received:
    1,321
    Also if you stop defining curves as bezier Vcarve should output the G-code for arcs. (you are using the correct post processor)
    Alex.:thumbsup:
     
  3. phoenix fab

    Builder

    Joined:
    Mar 12, 2019
    Messages:
    29
    Likes Received:
    3
    Ok will do.
    I haven’t noticed a difference in the cut quality between the two so I’ll stick to the circular arcs in vcarve. Glad I’m using the correct p/p.
     
    sharmstr and Alex Chambers like this.
  4. Gary Caruso

    Gary Caruso OpenBuilds Volunteer
    Staff Member Moderator Builder

    Joined:
    May 19, 2016
    Messages:
    1,184
    Likes Received:
    531
    i tossed the G-code you posted into UGS and it looks like nice smooth curves to me.
    Post your $$ settings from your xPro. This is belted? 20tooth? did you dual belt ?
    Cheers
    Gary

    upload_2019-8-13_18-47-21.png
     
  5. phoenix fab

    Builder

    Joined:
    Mar 12, 2019
    Messages:
    29
    Likes Received:
    3
    I’m glad is smooth on your end that confirms it’s a machine issue or setting issue.
    I’ll have to get the settings tomorrow at the shop.
     
  6. phoenix fab

    Builder

    Joined:
    Mar 12, 2019
    Messages:
    29
    Likes Received:
    3
    It’s a single belt 20 tooth pulley.
     
  7. Gary Caruso

    Gary Caruso OpenBuilds Volunteer
    Staff Member Moderator Builder

    Joined:
    May 19, 2016
    Messages:
    1,184
    Likes Received:
    531
    Dual belting will get you big benefits for cheap with 1500-3000mm belts. Just make sure to do it correctly :)
    Cheers
    Gary
     
    sharmstr likes this.
  8. phoenix fab

    Builder

    Joined:
    Mar 12, 2019
    Messages:
    29
    Likes Received:
    3
    upload_2019-8-14_8-56-9.png
    upload_2019-8-14_8-56-31.png
    upload_2019-8-14_8-57-8.png
    upload_2019-8-14_8-56-48.png
     
  9. Peter Van Der Walt

    Peter Van Der Walt OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Mar 1, 2017
    Messages:
    13,751
    Likes Received:
    4,070
    Next time, easier to copy/paste from the Serial Console tab (;
    Go to Serial Console
    At the bottom, send $$
    Select and Copy from the terminal above the input box
     
    sharmstr likes this.
  10. phoenix fab

    Builder

    Joined:
    Mar 12, 2019
    Messages:
    29
    Likes Received:
    3
    Ok great thank you
     
  11. Gary Caruso

    Gary Caruso OpenBuilds Volunteer
    Staff Member Moderator Builder

    Joined:
    May 19, 2016
    Messages:
    1,184
    Likes Received:
    531
    Hi Phoenix, your speeds and accelerations are a bit aggressive and can lead to the step-loss and chatter, try 5000mm/min max speed and 500mm/s^2 acceleration (1500mm/min should be fine on Z)
    Cheers
    Gary
     
  12. phoenix fab

    Builder

    Joined:
    Mar 12, 2019
    Messages:
    29
    Likes Received:
    3
    Ok I’ll make the adjustments and give it a shot
     

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice