Welcome to Our Community

Some features disabled for guests. Register Today.

Co2 Laser Cutter/Engraver Rotary Attachment

Discussion in 'Laser Cutters' started by pedrofernandez, Feb 4, 2019.

  1. pedrofernandez

    pedrofernandez Journeyman
    Builder Resident Builder

    Joined:
    May 14, 2017
    Messages:
    148
    Likes Received:
    219
    pedrofernandez published a new build:

    Read more about this build...
     
    leonardo roger likes this.
  2. Mark Carew

    Mark Carew OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jun 28, 2013
    Messages:
    2,742
    Likes Received:
    2,407
    Great job @pedrofernandez this looks really cool. I like how you have the freedom on this design to adjust one side up and down to allow for different bottle shapes.
     
    pedrofernandez likes this.
  3. pedrofernandez

    pedrofernandez Journeyman
    Builder Resident Builder

    Joined:
    May 14, 2017
    Messages:
    148
    Likes Received:
    219
    this was a half time show idea !!! that rotary is for the franken40 and will be attached to the z axis structure but removable not permanently fixed like the k40 cube, profile is tall in order to be able to engrave large beer mugs with handles cheers..
     
    Mark Carew likes this.
  4. CChico

    CChico New
    Builder

    Joined:
    Nov 21, 2018
    Messages:
    29
    Likes Received:
    96
    Let me know how you like it when it's finished. I use a chuck rotary and I love it. A few months back I purchased a rotary off of eBay with a similar design but I found it to be too jerky, especially when the print job was done and the machine would reset to the home position, the glass would just end up flying. Could have just been me though but I returned it. When I'm done with the current build (oh so close) I'm planning on making my own chuck rotary.

    I went ahead and added a link to the eBay listing. Hey, who knows if it turns out good you could make some money selling those. @$245 each there is a nice profit margin.

    Co2 Laser Rotary Engraver cutter attachment works with K40 x700 and others! | eBay
     
  5. pedrofernandez

    pedrofernandez Journeyman
    Builder Resident Builder

    Joined:
    May 14, 2017
    Messages:
    148
    Likes Received:
    219
    This is for the DSP controller, the one for the Cohesion board on the K40 Cube is all set and running with a dual stepper on series using GRBL-LPC 4 axis external driver firmware.
     
    CChico likes this.
  6. Satish Veda

    Builder

    Joined:
    Dec 21, 2018
    Messages:
    13
    Likes Received:
    1
    Hi Pedro,
    Very cool! A rotary Laser tool on a Laser cutter opens up so many more applications.
    Please keep us updated. Also, can you post a pic of the Yeti tumbler, that was worked on?
    It would be interesting to see the engraving detail. TIA.
    Regards,
     
  7. pedrofernandez

    pedrofernandez Journeyman
    Builder Resident Builder

    Joined:
    May 14, 2017
    Messages:
    148
    Likes Received:
    219
    Hi here is a test sample engraving over bare metal, using laserbond 100 yetitest2.jpg
    yetitest.jpg
     
    Mark Carew, GrayUK and Rick 2.0 like this.
  8. GrayUK

    GrayUK Openbuilds Team Elder
    Staff Member Moderator Builder

    Joined:
    May 5, 2014
    Messages:
    1,668
    Likes Received:
    627
    That looks great!
    I know very little about using lasers in reality, so it begs this question.
    I was thinking the other day about reflection? Do you not have to take care of any chance of reflection from the surface of, say, glass or similar?
    I know they do make a spray material for this sort of thing.
    Do you, or will you, be using something like that?
     
  9. pedrofernandez

    pedrofernandez Journeyman
    Builder Resident Builder

    Joined:
    May 14, 2017
    Messages:
    148
    Likes Received:
    219
    Normally you want to protect your self more from the "welder flash" generated at contact with the material with this lasers than a reflection, but the machine is covered with acrylic sheet on the lid and all safety precautions are taken in mind, The product used for engraving the bare metal SS is called Laserbond, Cermark, and many other brands, even CRC dry moly lube from your local autoparts will work but as well
     
    GrayUK likes this.
  10. papashay

    papashay New
    Builder

    Joined:
    Mar 13, 2019
    Messages:
    1
    Likes Received:
    0
    how can I build this?
     
  11. joe fel

    joe fel New
    Builder

    Joined:
    Jun 10, 2019
    Messages:
    3
    Likes Received:
    0
    I would like to know what size belt and pulleys he used..............
     
  12. pedrofernandez

    pedrofernandez Journeyman
    Builder Resident Builder

    Joined:
    May 14, 2017
    Messages:
    148
    Likes Received:
    219
    Belts is a 200mm x 6mm close loop Gt2 pulleys are 2-40 teeth for 6mm belt ans one 16 teeth for 6mm belt 4-5x8x16 bearings a 8mm rod.
     
    joe fel likes this.
  13. joe fel

    joe fel New
    Builder

    Joined:
    Jun 10, 2019
    Messages:
    3
    Likes Received:
    0
    Could you please tell me the specs on the stepper motor I made a rotary but was not sure if the motor I have will effect the images. I got nema 17 1.8 degree 1.5a Could you please tell me what you used? Thanks in advance
     
  14. pedrofernandez

    pedrofernandez Journeyman
    Builder Resident Builder

    Joined:
    May 14, 2017
    Messages:
    148
    Likes Received:
    219
    It should work, what controller you have? pulleys combination, and type of belt?
     
  15. joe fel

    joe fel New
    Builder

    Joined:
    Jun 10, 2019
    Messages:
    3
    Likes Received:
    0
    I bought the belt and pulleys you suggested...But it seems everywhere I am reading about the steppers for the lasers they all are 0.9 degrees and I did build the rotary but it when I do something the artwork is distorted like a circle will be an oval... Any suggestions I am using the K40 with Corelaser....? Thanks for getting back to me so fast
     
  16. pedrofernandez

    pedrofernandez Journeyman
    Builder Resident Builder

    Joined:
    May 14, 2017
    Messages:
    148
    Likes Received:
    219
    I use different type of controllers that allow me to change the step pulse configuration, in the case of your stock K40 M2 Nano controller that is not posible, even using a 0.9 Deg motor will cause distortion unless your round object circumference is perfectly match to the controller configuration, so you will need to distort you graphic in order to have a good result, my suggestion for you is to upgrade your machine controller with a Cohesion laser board that it is a drop in replacement for the M2 Nano and get Lightburn software, the good thing about, it is the dedicated extra stepper driver for a rotary axis and be controlled via the software, some people find the laser board a bit over price but it worth the change, also the firmware is very easy to edit and make your rotor work like a charm.
     
  17. 3DPTR

    3DPTR New
    Builder

    Joined:
    Jul 23, 2018
    Messages:
    5
    Likes Received:
    0
    Where did you get the main drive wheels?
     
  18. Randy Alexander

    Builder

    Joined:
    Mar 29, 2018
    Messages:
    1
    Likes Received:
    0
    Do you offer the plans to build this, i.e. 3D parts or drawings?
     
  19. Giarc

    Giarc OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Jan 24, 2015
    Messages:
    2,898
    Likes Received:
    1,613
    I see lots of questions here. Although no apparent info on the rotary axis, I noticed on his machine the website Welcome to Franken 40 Build Project - DIY K40 Laser where there is a ton of detail on the rest of the build. Good stuff! I can't wait to modify my K40.
     
  20. pedrofernandez

    pedrofernandez Journeyman
    Builder Resident Builder

    Joined:
    May 14, 2017
    Messages:
    148
    Likes Received:
    219
    ill post laser cut dxf files for this
     
  21. Prometheus

    Builder

    Joined:
    Mar 21, 2015
    Messages:
    17
    Likes Received:
    0
    Any update on the files for this build? Interested in the STL files for those drive wheels also as it seems all of us are ;) GREAT build!
     
  22. pedrofernandez

    pedrofernandez Journeyman
    Builder Resident Builder

    Joined:
    May 14, 2017
    Messages:
    148
    Likes Received:
    219
    Hello guys Im working in a design change ill post it this week

    thanks
     
    Giarc likes this.
  23. Neil Rosenberg

    Neil Rosenberg Journeyman
    Builder

    Joined:
    Dec 29, 2013
    Messages:
    179
    Likes Received:
    177
    Very interesting design, I hope the files are soon to be uploaded. Eager to try it!
     
    #23 Neil Rosenberg, Sep 24, 2019
    Last edited: Sep 24, 2019
    Prometheus likes this.
  24. Matthew King

    Builder

    Joined:
    Sep 28, 2019
    Messages:
    1
    Likes Received:
    0
    Fantastic build! One question I have, did you print the end plates or purchase them? I'd love to build this but don't have a 3D printer (currently).
     
  25. pedrofernandez

    pedrofernandez Journeyman
    Builder Resident Builder

    Joined:
    May 14, 2017
    Messages:
    148
    Likes Received:
    219
    laser cut 1/4 in acrylic plates files and final design soon will be posted
     
  26. Cyberned

    Cyberned New
    Builder

    Joined:
    May 31, 2017
    Messages:
    4
    Likes Received:
    0
    What are the main drive wheels called. I'm trying to see where I can get some to try this out.
     
  27. pedrofernandez

    pedrofernandez Journeyman
    Builder Resident Builder

    Joined:
    May 14, 2017
    Messages:
    148
    Likes Received:
    219
    Hi Im on the process of making a video how to to design them for 3d print them, also an stl file will posted IMG-1830.JPG IMG-1831.JPG IMG-1832.JPG IMG-1833.JPG IMG-1834.JPG IMG-1836.JPG
     
  28. Cyberned

    Cyberned New
    Builder

    Joined:
    May 31, 2017
    Messages:
    4
    Likes Received:
    0
    Thanks for the update. Would you provide the size of the O-Rings used in your video?
     
  29. pedrofernandez

    pedrofernandez Journeyman
    Builder Resident Builder

    Joined:
    May 14, 2017
    Messages:
    148
    Likes Received:
    219
    you will need this
    uxcell O-Rings Nitrile Rubber, 40mm Inner Diameter, 50mm OD, 5mm Width and
    uxcell O-Rings Nitrile Rubber, 15mm Inner Diameter, 25mm OD, 5mm Width for the free wheels

    the pulley used is
    60 teeth Aluminum Bore 8mm GT2 Timing Pulley for 6mm Width belt
     
  30. Cyberned

    Cyberned New
    Builder

    Joined:
    May 31, 2017
    Messages:
    4
    Likes Received:
    0
    any time line for releasing the STL file?
     

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice