Welcome to Our Community

Some features disabled for guests. Register Today.

pzl help me make 3d printer using arduino and cnc shild

Discussion in '3D printers' started by elcobenoz, Feb 21, 2017.

  1. elcobenoz

    elcobenoz New
    Builder

    Joined:
    Feb 21, 2017
    Messages:
    5
    Likes Received:
    0
    Hi, i made a cnc machine already using cd drives and a cnc sheild (red one).
    I want to make a 3d printer using a pen, ive seen videos where they use a pen, and they trigger the buttons usin arduino (spindle0 i have no clue where the spindle is on the cnc sheild and how to put it on and what to do. Please help, diagram or picture swould really help me XD
     
  2. evilc66

    evilc66 Journeyman
    Builder

    Joined:
    Jan 9, 2015
    Messages:
    392
    Likes Received:
    153
    You mean, using a 3D printing pen like a 3 Doodler? Is there a specific reason you would want to go that way rather than make a more traditional setup with a higher power extruder and hotend? You may run into some issues with the host software (Repetier, Simplify3D, Pronterface, etc...) not having any control or feedback from the hotend for temperature control.

    If you do want to continue with the pen idea, then you are going to have to be more specific about which pen you are using, and the CNC shield that you have.
     
  3. elcobenoz

    elcobenoz New
    Builder

    Joined:
    Feb 21, 2017
    Messages:
    5
    Likes Received:
    0
    Its a cnc sheild v3 and the pen i am going to get is 20x 1.75mm ABS Printing Filament Modeling For 3D Printer Pen Drawing Pen 10M/Per | eBay
     
  4. evilc66

    evilc66 Journeyman
    Builder

    Joined:
    Jan 9, 2015
    Messages:
    392
    Likes Received:
    153
    Well, the link was just for filament. Anyway the same question as earlier still stands. Why buy the pen, when you can get a more accurate, repeatable, and reliable setup with a dedicated extruder and hot end that was designed for use with a 3D printer? If cost is a concern, you can get Chinese knock off parts for dirt cheap. You should be able to get a MK8 extruder and hot end for under $40.
     
  5. elcobenoz

    elcobenoz New
    Builder

    Joined:
    Feb 21, 2017
    Messages:
    5
    Likes Received:
    0
     
  6. evilc66

    evilc66 Journeyman
    Builder

    Joined:
    Jan 9, 2015
    Messages:
    392
    Likes Received:
    153
    You will most likely want to use the spindle enable pin, which you can find on the right side of the board labeled SpnEn

    [​IMG]

    Now, I have no idea what the control voltages are on the 3D pen, so you are on your own on that one. Same with modifying the g-code to make it all work.

    I'm sure you have your reasons for doing it this way, but using more traditional parts to make a 3D printer will make your life a lot easier. A Ramps 1.4 shield loaded with Marlin firmware would make this far easier.
     
  7. elcobenoz

    elcobenoz New
    Builder

    Joined:
    Feb 21, 2017
    Messages:
    5
    Likes Received:
    0
    Ye i know, i said with the cheap mk8 china one and with extruder and hotend how would i wire that up?
     
  8. evilc66

    evilc66 Journeyman
    Builder

    Joined:
    Jan 9, 2015
    Messages:
    392
    Likes Received:
    153
    The CNC shield won't be able to handle it, as it doesn't have connections for the thermistor input and the heater output. For this, it really is going to be easier to use a Ramps board with an Arduino Mega2560. It has all the connections you need for a 3D printer, and because it's used so much, there is a ton of information out there on how to connect the hardware, and configure the software. It also helps that it's dirt cheap.
     
  9. elcobenoz

    elcobenoz New
    Builder

    Joined:
    Feb 21, 2017
    Messages:
    5
    Likes Received:
    0
    OK thanks man, could you find me on ebay a 3d printer frame as i have been searching for DAYS cantcan find them. (in uk website plz)
     
  10. evilc66

    evilc66 Journeyman
    Builder

    Joined:
    Jan 9, 2015
    Messages:
    392
    Likes Received:
    153
    If you are going to buy a Ramps board, drivers, Arduino Mega2560, hot end, extruder, and now looking for a 3D printer frame, why not just buy a complete printer? You can get prusa i3 clones pretty cheap with everything you need to get going (just avoid the acrylic framed ones).
     

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice