OpenBuilds CONTROL Software

Thanks for this link, I will check out the example config on bdring's github.

 

I have the same problem on BB32

 

I would BUT, the BB32 is dead, My interface is dead when I tried to connect to BB original, interface is dead Have no idea what is happening!!~

 

Thanks for the link, but I am afraid it's a bit worse than that. The system will not connect with BB32. I have downgraded to my original BB and the interface is dead now. I tried 3 different USB cables (ruled it out). two separate laptops, the HP that I dedicated to CNC (just disconnected and will not connect again) and Lenovo (that said the BB32 was trying to draw too much power and would not connect). Thanks!

 

I went over the article you sent again, It didn't have firmware failure, it stated up, could not/ would not find a USB connection to the black box. This occurred when I was fitting a dust shoe, so no commands were being sent, it was already wired to the machine with the connections I had on my first black box (this was an upgrade to BB32)..
6.3.2 Make sure you are connecting to the correct port, at this point It would not/could not find a communications port on the BB32, when I switched back to BB it had no problem with the connection. Besides this my interface is dead also and yes, I changed the cables to match the units. Thank you very much for your suggestions and help!

 

I thought I posted reply but didn't see it.... anyway, wanted to say Thank you for the Award !! lol

 

The interface is dead. The BB32 will power up, it will not connect to a laptop, after trying both laptops I have, I ordered a new laptop to be sure it's not that. Also

• 6.3.1 Incorrect Wiring It was wired for the original BB, all connections are the same, so it was not wired wrong, as wired it powers up the BB and BB32 starts up it cannot connect laptop to BB32 it will not produce a signal (no com port).
• 6.3.2 Make sure you are connecting to the correct port, all ports were correct for BB and connected without problem to BB32, so I used the correct ports.3
  • 6.3.3 Check Device Manager, I am sure I did this, I had to do it when I was building a Chinese control box. Then I decided {as I should have first) buy American. And I could not get clear answer from the Chinese.
  • 6.3.4 Update Drivers I have software that checks drivers each time a computer is connected. And I checked to be sure there were no windows updates.
  • 6.3.5 Computer problems the reason I order a new laptop the Lenovo (laptop) gave a message when I tried connecting with it, (not exactly sure of verbiage) but said the BB32 was trying to draw more power than it would allow' and that was the end of that testing!
  • 6.3.6 Contact the OpenBuilds Partstore, other than posting with you I did send a request for help, still waiting for their reply.

As it sets now, I think I will order another BB32 and interface and try it all over again. Yes that will be expensive but I sit here with a machine that I worked on every damm day and have for over a year. Until BB it would do nothing, and I still think BB is one of the best products available!!

No the dust shoe did not cause the problem, did not hit a relay when fitting it.

 

I understand what you are saying, but why would the BB (not BB32) connect with no problems at all if the (any)wires were chaffed or damaged. Just asking before tearing the machine down and restart from the beginning. I do not place blame on Open Builds or BB, My only point was to find a solution. So when I replied to you, I was attempting to provide the steps I have done, I am not arguing with your advice and hope you don't feel I am. All wiring is complete and wrapped, it consists of 4 conductors, shielded cable, the stops I purchased from Open Builds and all work properly.

 

Are you the support contact? I sent a question about if I purchase new, can I send the existing ones in for repair. Thinking about when I get new, I will have disassembled everything and start new (still using 4 conductors with shield cable). I have a VFD, a relay to power vacuum (dust removal) and a connection for air pump.

I just remembered that just before or close to it I added a EMI filter. Please understand I am 72 years old and trying hard to get ahold of this technology, so if I seem kinda slow.....

But for now, I will order new and hope they can be returned for (the ones I screwed up somehow for repair(s), I didn't get an answer from submitting a ticket, so I will make a walk of faith.

Thanks again for you're help!

 

I searched for mean well EMI but cannot find a listing or available place to order, I checked both Amazon and ebay, neither have anything close. I did find

Single-Phase General-Purpose DIN Rail Mount Filters
Roxburgh DRF series DIN rail mounted single-stage filters are specifically designed as line filters for 120/240 VAC devices. They provide good performance for both common mode and differential mode interference and are rated up to 250V. Typical applications include PLC control applications, security, test, and monitoring equipment.

• 0-250 VAC/VDC, 0-60 Hz, single-phase
• Current ratings from 1A to 10A
• Plastic housing with a slim profile
• Snap on to 35mm DIN rail for ease of mounting in a cabinet

I am guessing something similar is what you are making reference to? I will send picture of the one I have as soon as my iphone charges enough.. I don't know what amperage the BB32 requires but will be sure I know before ordering.

 

I am using Mean Well LRS-350-24, with a purchased front end from Open Builds. I was mistaken. I thought you said to use a Mean Well EMI filter. And have found close to that brand starting at $50 to several thousand, common sense tells me if it costs more to provide a filter that costs more than the equipment, then I should be looking for a differing setup, Sorry i misunderstood.

 

Thank you once again for your advice. I will remove it as I am replacing all the wiring. Should I still use shielded cable?

 

When I began this path, I had no idea about anything related, I purchased the CnC and expanded it immediately, the control that came with was junk, so I opted to build one using a control base from China (big mistake) I purchased all the parts required (that was very expensive)I have power supplies (about) six of them, they required 3 power supplies. For the unit, I have stepper motors (6). it goes on and on, before I found OB. The idea to set up the machine itself is from all over the Net. I have the suggested relay set-up for air and dust removal, I have a rheostat to control the speed of DeWalt router as spindle. I have a VFD with 24000 RPM air cooled spindle setup now. I have a separate Mean Well power supply (MDR-60-12) to power (?) I will find out when I am removing wires. So, I would say everything I did was according to information on web or Facebook videos. Now if you want to build a hospital or other commercial building, I have 56 years in that business, but your world of electronics is unfamiliar to me.

Thanks
Larry

 

Who do I contact to send these (first BB32 and interface) in for repair? And it's very odd the original BB was a fused unit and the new has no protection like that? I asked support the same question but haven't heard back yet, perhaps it is under the cover?

 

Then if the fuse is to prevent fire....Glad I am hearing that now that I have moved on to bb32, my machines are set in a spare bedroom and it would have burnt house down. Any more good tidings as we progress?

The BB32 Is under power right now has been for well over an hour, first thing I notice is the fan has not/does not run. I found an internal jumper for setting voltage on the stops, mine are 5 volt and it was factory set for 24 v. Don't remember seeing that in manual!