Laser Cutter Builds
Build Author skarab Views 58615
Much4 - LaserV printed version
By following the way of Robert Hummel, I drew a version of its exellent Laser V to use NEMA17 and easily printable parts.
Build Author Ariel Yahni Views 30031
Modifying the K40 laser cuter stock gantry in favor of OpenBuilds superior and smoother movement. Also will provide me a better level control for easier beam alignment.
Build Author HPB Views 28536
A simple XY laser engraver/cutter
A simple low-cost XY plane laser engraver/cutter inspired by the Much 4 laser build, with minimal parts and assembly time. Uses standard off the shelf components in almost 90% of the build with the exception of the axes motor and wheel mounts which need to be 3D printed.
Build Author pedrofernandez Views 10009
Openbuilds Table Top 50w Co2 Laser Cutter/Engraver
DIY build of a Co2 Laser cutter/engraver 12x24 working area.
Build Author CChico Views 14066
Custom build 80w Co2 Laser Cutter
Building a custom made 80W Co2 Laser cutter. Making it from scratch and it's a work in progress but I've learned a lot and I'll be sharing a bit of that knowledge with you guys since I've learned a lot from here.
Build Author LukasK Views 10543
I have completed some custom build 3d printers (i3 and delta style) and a cnc mill based on v-slot and c-beam. From the beginning the cnc was built to fit/change between router, 5w led laser module and plotter pen. While all three works great, the build is primarily focused on heavy duty milling and brings some disadvantages when it comes to laser - slow because of leadscrew motion system and not as powerful because of “only” led laser. That is why I have started this build of co2 laser machine.
Build Author Mohammed Iskandarani Views 17061
CO2 60 -130 WATT LASER ENGRAVING/CUTTING CNC WITH DSP AWC608 CONTROLLER
LASER ENGRAVING DIY 60 WATT
Build Author mytechno3d Views 20547
A low cost and easy to build laser cutter based on 2.8w laser diode .
Build Author petethepig Views 3808
OpenBuilds ACRO Z Axis
Z-Axis for OpenBuilds ACRO system. It is sturdy enough to carry a small drill.
Build Author viktop Views 5476
Simple Cnc System (arduino Grbl)
Arduino powered simple CNC system using GRBL firmware. Designed to give the most function using the very least number of parts at the lowest price.
Build Author inhan Views 15892
Openbuilds rovo laser mini(오픈빌드)
laser mini 20 * 40 OPENBUILDS base frame.(크기 412x455mm) laser mini 20*40 기본프레임입니다. 기존 여러부품을 사용한 제품보다 부품수를 줄이면서 최소한의 단가를 뽑을려고 디자인했습니다.. 기존대비 부품수 절반에 단가도 절반을 줄이면서 최적의성능을 내려합니다.
Build Author Yoshiya Arii Views 27195
V-Slot Laser cutter and engraver
The Smart Laser Mini is an open source such as use Raspberry pi. Easy to assemble type of desktop laser cutter and engraver. Also we used V-slot
Build Author pedrofernandez Views 4205
The Franken Rotor
Yes another K40 Franken machine dedicated for round objects,,,
Build Author blindflight Views 7045
This is a mount I wanted to build for a laser project using OpenBuilds part router mount.
Build Author joetemus Views 9754
K40 ACRO Conversion
A K40 to ACRO Co2 laser cutter build. Designed and built to expand the work area of the K40
Build Author Lumberjack Engineering Views 12529
SOLAC: Space Optimized LAser Cutter
The Space Optimized LAser Cutter is a 40 watt CO2 laser cutter that supports a maximum part volume of 24" x 16" x 6.25". It consists of a V-slot frame + brackets/mounts designed to be 3D printed on a consumer desktop printer. Total cost of the machine is ~ $1,400 USD.
Build Author Kyo Views 6732
3-Axis CNC Laser Engraver running grbl 1.1 in laser mode and Laserweb4.
Build Author Lasersc Views 1559
The D & R TigerPaw Trilogy
Hopefully this will be a quick guide to one way that you can add a laser to an existing CNC router.
Build Author pedrofernandez Views 5776
Co2 Laser Cutter/Engraver Rotary Attachment
Vslot rail system at work again, laser cutter/engraver rotary device for cylindrical objects .
Build Author Rick 2.0 Views 2911
Minimalist Laser Platform
Minimalist laser platform built with Makerlink connectors and modified Nema 17 stepper mounts used as gantry plates.
Build Author Bernie CLark Views 5607
C-Beam XXLarge "Laser "Tank""
A re-imagining of Dollarz81's XXL Tank in Laser form
Build Author infectedfpv Views 3459
3D printed Laser Engraver
i´ve designing this laser taking care of every part to be functional, This laser has Endstops mounts on the corners and the X axis both sides too. The corners has fasbelt tension knobs for easy operation. The laser mount has adjustable knob to manually rise or down the laser for focusing purpose. all the parts have been printed at 65% infill a 2 perimeter lines just to make the parts stronger. Attached you will find a part list with quantity and link where to buy. SIZE 1mts x 75cm Built area
Build Author RobSaunders Views 10005
Laser Cutter/Engraver OptLaser 6W with Z-axis
This was my first attempt for a laser platform. I'm using the OpenBuilds ACRO 20"x40 platform, 6W OptLaser, homemade z height and the xPro driver board.
Build Author RobSaunders Views 7537
Z-Axis for Laser Diode
Custom Z Axis for OptLaser 6watt and the Acro System
Build Author Karan Singh Sisodia Views 4032
CoreXY based CNC Laser machine.
Build Author Mike Campbell Views 184
Piggy back engraver for ShopBot
Built from leftover T-Slot extrusions plates and hardware from other defunct projects.
Build Author BNMaker Views 4262
A minimalist 2-axis A2 sized laser diode cutter/engraver. Designed to give the most function using the very least number of parts at the lowest price.
Build Author DistortedDesigns Views 27775
Project Death Star - DistortedDesigns Laser Engraver
2 watt Laser Engraver, Simple, Fairly Low Cost, and Portable
Build Author Superslinky Views 4520
K40 Laser Build (Major Changes)
Major K40 Laser Mod
Build Author Robert Hummel Views 132825
With such great success/attention my laser got, I ended up with a good friend that would like to dabble in stencil art and so I have decided to share my build with him and you here :) I will be using all the same electronics as in my previous build except the driver boards I will be using are the famous reprap 4988's they are more easy to come by and cost less. I will also be using open builds mini v wheels/v groove extrusion just so I can get a feel for their versatile products
Build Author openhardwarecoza Views 58462
openBuilds FreeBURN-1 V-slot CO2 Laser (60-100w)
DIY Lasercutter: Budget orientated, medium sized (60-100w), safety first, based on Lasersaur software toolchain
Build Author Chris Anderson Views 32991
Openbuilds Co2 80w Laser Cutter
Co2 80 watt openbuilds laser cutter, 1200mm laser tube, 1500x1000x500mm dimensions. Build frame first and then panels to be added.
Build Author Kims3DIY Views 7702
Beamlazer Laser cutter CO2 100W
Hi everyone, im new to the world of lasercutters but i have been granted access for a Trotec laser for a while with old firmware and only compability trought Windows XP. Then i decided to build my own laser, with some easier workflow and support for Windows 10. Since im still a student i have limited resources, so i will try too use scrap parts as much as possible. I will publish photos and updates during my build continously. Gladly taking advices from others.
Build Author pedrofernandez Views 8102
The Franken Forty
This is a K40 machine conversion!!
Build Author jpjoshua Views 5686
Arduino Grbl Laser CNC
Arduino powered Laser CNC using GRBl firmware.
Build Author Puddin Views 9300
100w Laser Cutter Build Log
I rebuild my 2 meter tall 3D printer into a 100w laser cutter
Build Author pedrofernandez Views 3658
The Acro Laser Machine Build
Build Author cory stafford Views 2410
Home built laser cutter
This is a laser cutter built with intent to use arduino as controller for a co2 cutting laser.
Build Author pedrofernandez Views 3132
Laser Rotary Tool / Attachment
Rotary attachment to engrave cylindrical objects on laser machines
Build Author Jurgen Views 6488
laser add-on for C-Beam machine
3.8 W laser add-on for C-Beam machine. Can easily be swapped with the router.
Build Author Joelosborn Views 799
Project Infinity co2 laser
1m x 1.8m 60w co2 laser build.
Build Author Andrew Hague Views 7704
Laseroko Laser Engraver Build
After expanding a Shapeoko 2 with the rails and motors left over, make yourself a laser engraver.
Build Author Lindsey Lewis Views 4257
Update Eleksmaker with Openbuild eccentrics for X-Carriage
A simple approach to making the Eleksmaker A3 Laser build have a better functioning X-Carriage! Of course this assumes you bought an Eleksmaker A3 or plan to.
Build Author Giarc Views 2093
ORCA Laser Build
This is my take on the Acro Laser system made from mostly salvaged, scrap, or leftover parts. I modified the plates in an attempt to maximize the cutting area and I wanted a lightweight adjustable Z axis.
Build Author MTO Views 2764
4' by 2' Lasercutter
4foot by 2 foot, 10W El-Cheapo blue laser
Build Author Bruce Walker Views 760
BD's Burn Box - ACRO Laser Engraver System
Two plus years in the making, I finally have a working ACRO 510 laser engraver system complete with enclosure and air filtration.
Build Author Metalguru Views 7803
Small Laser Engraver Concept
Low cost Laser Engraver build using all off-the-shelf components.
Build Author Ollieg Views 766
Hevavy duty 1300mm x 1300mm laser cutter Ceramic tube Servo motors
Starting the next Laser build, Plan to complete within 60 days.
Build Author wackocrash5150 Views 1431
45W CO2 Laser Build
A co2 laser build that is heavily inspired and based quite a bit off Pedro Fernandez' 50w co2 laser build. This is my first build post so, bare with me.
Build Author JCPhlux Views 3034
Phlux Core XY Laser Etcher
A 750mm x 1000mm Core XY Laser Etcher/Cutter. To cut down on cost I tried to have as many parts as possible be printed.
Build Author Anthony Bolgar Views 11860
Just a little light duty laser engraver.
Build Author Rob Taylor Views 7845
Portable Diode Laser Cutter
Integrating custom machined components and off-the-shelf CNC components to create a portable diode laser etcher with air assist and reasonably substantial z-axis travel.
Build Author tshilling Views 4857
K40 12x24in rebuild (In Original Case)
Rebuilt the internals of a K40 to allow for a 12 x 24 in cutting area while reusing the same external case and not touching the laser tube.
Build Author Sjors Views 6670
Laser cutter project by students
This build is made by students from Fontys Hogescholen Eindhoven, department Engineering. Every quarter a new group continues the work of the previous group. We have been working on the project since september 2015, and as it is a work in progress, a lot will be added later. The first months have mainly been about designing and building an XY-table on which later all the electronic components will be added and the laser.
Build Author snokid Views 5766
http://www.buildlog.net/sm_laser/drawings.html using this as a baseline.... Going to try and use all or most off the shelf parts.
Build Author Cipta inovasi Views 4798
laser gantry use mini v end block my own design
i always make laser cutting machine, but when i see openbuilds, this can make more cheap gantry for make laser cutting.
Build Author MConner Views 6737
Fun and Functional Laser Build
A very fun and fulfilling build. I can't say enough about the whole Open Builds site and Open Source movement. I strongly believe this is the fastest and most creative way of getting ideas out of the mind, and onto the floor.
Build Author Anthony Bolgar Views 7901
CO2 Tube life expectancy experiment - Sponsored in part by Openbuilds
Hypothesis - Running CO2 laser tubes at high amperage may shoirten tube life in number of hours, but will be made up for by the increase in actual inches engraved/cut using the higher power. This is a long term experiment, so the build status will remain as "Build in progress" until the experiment has been completed.
Build Author sybren Views 3728
80watt Lasercutter, workingarea 105x52[cm], steel frame
I will write a short buildlog here with mostly pictures. I designed this lasercutter in solidworks(not totally finished) for a good overview and such that the steel tubes could be lasercut by a company, the metal frame is based on the lasercutter the KÄSER, which you can find on cnczone.nl. The mechical parts are designed by myself because I had no mill to my use, so the mechnical parts are lasercut(same company as tube) steelplates welded together.
Build Author pedrofernandez Views 4427
K40 Cube Laser Cutter
The k40 cube is a laser cutter build using mostly stock parts of the chinese k40 laser
Build Author Michail Views 1229
x_y_module laser engraver
low cost 2 axis cnc laser, really portable and easily expandable
Build Author Tim Butler Views 5329
CO2 laser cutter
A build which is based on a metal frame and aluminium plate which I salvaged from a skip. The frame is sized to hold 19" rack units so I'll build my control box into a 3U rack unit (also salvaged). The area available for the build is 700x1200mm. I'll sling a 60W CO2 tube under the base, the beam path will be initially upward into the enclosure.
Build Author jnsbanman Views 413
A new design of my based on a couple different machines I have seen both on openbuilds and youtube. In the end will have a and X/Y workspace of 1250mm x 1000mm and a Z axis range of about 200mm.
Build Author megashub Views 11504
K40 C02 Laser Rail System
An Openbuilds replacement rail system for the common eBay "K40" C02 Laser Cutter
Build Author dddman Views 7230
60W CNC Laser build
Laser CNC, 60W, didn't have one yet... have to :) This build is a retrofit of a surgical laser into a CNC.
Build Author Neil Rosenberg Views 1236
Rotary Axis for Laser Engraver/Cutter
This is a fully adjustable, low profile rotary axis for your Laser Cutter. Many OpenBuilds components are used, plus a handful of 3D printed parts.
Build Author Anthony Bolgar Views 8475
L'FOX - Large Format OX deriviative. Designed and built by Revision 13 Prototypes
This build is for a testing rig to use while testing out different controller boards and CAM software for milling and routing. It is in the early stages, planning is complete, parts are ordered. Awaiting parts delivery to start build. Please not the BOM only covers parts from the OpenBuilds part store. I will be posting the other required items very shortly.
Build Author RussB Views 4915
New 2 watt laser platform
Acro based 2 watt laser platform
Build Author holographic Views 2409
How i construct and create my DIY Co2 Laser cutter and engraving mashine. details will follow
Build Author Max_Sijbers_Mechatr... Views 7633
In the expo projects during the second year of engineering students. the project group who made this rapport made a laser cutter for the students of Fontys Hogeschool Engineering to use this machine for creating parts for their projects. The goal of Project Laser Cutter is to build a laser cutter, which is safe and can be used within the school. Also it has to be able to cut through 10 millimetres thick acrylic material or 10 millimetres thick plywood. This project will follow the V-model. This
Build Author shadowtec Views 2501
My 80w Laser build (1000x1000 cutting area)
This is a 80w laser which I am building (picture of the case) the frame is constructed with normal square tubing with plastic corners. this laser needs to live outside
Build Author Sam Price Views 2295
Acros with customizations [WIP]
This is a work in progress ACROS build with new legs and wire tracks.
Build Author CLAUDIO MIKLOS Views 3913
ACRO 150 X 150 CM
Build Author JCPhlux Views 15407
Large 1500x1000 Laser V
I am building a Laser cutter based off Robert Hummel's Laser V design.
Build Author Cody Kesler Views 1891
Vacuum laser table
Large 10’x6’ vacuum table made from steel tubing and 1/4 inch steel plate
Build Author Hilleke Views 3254
Acro System cable management and enclosure
wooden parts of the enclosure can be removed easily used the existing extraction of my glass bead burners
Build Author Handy_Nord Views 1069
300x300 belt drive laser etching/cutting platform. The design was borrowed from another's blog and customized to fit materials on-hand. Was a very fun project to assemble.
Build Author Patto21 Views 655
Large format laser
Large format laser build for Student use at my school as well as some personal use.
Build Author Jean-Francois Talbot Views 4119
A 2 axis laser engraving machine, with a manual Z axis.
Build Author COMsulting Views 6383
1x1 Meter Laser Engraver
Building of a big open frame laser engraver.
Build Author Glenn Weston Views 4841
"AcroCadabra" My Acro Laser built with my C-Beam XL
Well I built a C-Beam XL around a year ago, I am still learning things as I make stuff with it, it has been quite a wonderful learning experience. Now I have gained enough confidence and knowhow to Mill the required Plates to build an Acro Laser System using the Acro Laser Sketchup Model. I have pulled the Model apart in Sketchup, isolated the Plates and generated the G-Code to cut/Mill the plates. I have used Sketchucam to generate the G-Code. I Use Mach3 on my C-Beam XL to Mill.
Build Author silverchris Views 1652
Silverchris's Laser Cutter
Work in Progress of a laser cutter design. Based on the CoreXY build from https://makerstore.com.au
Build Author quyngan Views 3342
DIY LED acrylic lamp
This is a simple lamp using only 2 LEDs & 2 AAA batteries.
Build Author Shannon Jardine Views 5839
Large Laser cut table build
Large 6 x 10 foot laser table build. New to building CNC