Welcome to Our Community

Some features disabled for guests. Register Today.

Sign Up

Recent Content by UltiBots

  1. UltiBots
    Post

    OpenBuilds CONTROL Software

    OK... thanks for your contributions!
    Post by: UltiBots, Dec 9, 2021 in forum: Control Software
  2. UltiBots
    Post

    OpenBuilds CONTROL Software

    Hi Devs... any chance in adding a confirm RUN popup? Run is so close to the OPEN dropdown... just after loading gcode... my mouse moved and BAM!!!...
    Post by: UltiBots, Dec 8, 2021 in forum: Control Software
  3. UltiBots
    Post

    VFD & IOT... how to wire/configure BlackBox

    **** Peter... you are fast. I edited my post but it was too late. Thanks for the help :)
    Post by: UltiBots, Dec 8, 2021 in forum: CNC Mills/Routers
  4. UltiBots
    Post

    VFD & IOT... how to wire/configure BlackBox

    Jim - I have the Huanyang HY01D511B VFD and 1.5kW spindle. I will look at using the VFD features to trigger the IOT power strip. Peter - Just...
    Post by: UltiBots, Dec 8, 2021 in forum: CNC Mills/Routers
  5. UltiBots
    Thread

    VFD & IOT... how to wire/configure BlackBox

    Hi all - I upgraded my Dewalt 611 to a 1.5kW VFD spindle. Before the mod I used the IOT relay to power the router and flood pump from BlackBox's...
    Thread by: UltiBots, Dec 7, 2021, 8 replies, in forum: CNC Mills/Routers
  6. UltiBots
    Post

    Running OB Control in VS Code debugger...

    Thanks for the reply... I was able to connect and get a snapshot. But this doesn't appear to allow me to debug with watchpoints, examine...
    Post by: UltiBots, Feb 17, 2021 in forum: Control Software
  7. UltiBots
    Thread

    Running OB Control in VS Code debugger...

    Hi All - I've been exploring changes to the OpenBuilds CONTROL software using VS Code. I am successful in making changes to probing function and...
    Thread by: UltiBots, Feb 16, 2021, 6 replies, in forum: Control Software
  8. UltiBots
    Post

    Drewtronics Touch Probe

    I'd reach out to Drew [email protected] :)
    Post by: UltiBots, Feb 15, 2021 in forum: CNC Mills/Routers
  9. UltiBots
    Thread

    Drewtronics Touch Probe

    Hi All... I am so impressed with the #Drewtronics touch probe and the #OpenBuilds Control hardware and software that I needed to share. Getting...
    Thread by: UltiBots, Feb 13, 2021, 3 replies, in forum: CNC Mills/Routers
  10. UltiBots
    Post

    OpenBuilds LEAD CNC

    I cut 6mm Aluminum sheet with my C-Beam Router to make plates for my CB3030. 1/8" (.1250") single flute carbide endmills for plastic -...
    Post by: UltiBots, Mar 12, 2020 in forum: CNC Mills/Routers
  11. UltiBots
    Post

    OpenBuilds LEAD CNC

    Going to test without... but if I get weird triggers/steps... shielding 4 me :)
    Post by: UltiBots, Feb 20, 2020 in forum: CNC Mills/Routers
  12. UltiBots
    Post

    OpenBuilds LEAD CNC

    Good to know. I'm using Xtension limit switches. Might try both :) Thanks!
    Post by: UltiBots, Feb 20, 2020 in forum: CNC Mills/Routers
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice