Welcome to Our Community

Some features disabled for guests. Register Today.

Cartesian Style Bots

Indie i2

Mar 10, 2021
Category
Cartesian Style Bots
Build Progress
Build Complete!

A lightweight, portable, accurate 3D Printer that has a good sized print area and small overall footprint that is easy to build, with easy to source components. The design is OpenSource allowing those with the capability to make their own parts get up and running.

Lautr3k RepRap

Feb 12, 2015
Category
Cartesian Style Bots

A 3D printer without belts, a print volume of 320x320x260mm, obviously the V-Slot as linear guide! and a maximum of printed pieces.

Dash-X 3D Printer: Innovative design

Mar 21, 2020
Category
Cartesian Style Bots
Build Progress
Build Complete!

Cross-beam Cartesian 3d printer with dual master/slave lightweight fiberglass drive shafts, BMG style extruder with Bowden (Capricorn) tubing. Hot end is Creality Ender 3 style with two fans and BLTouch for autoleveling. Filament runout sensor is also included.

OneZ i3

Apr 19, 2017
Category
Cartesian Style Bots
Build Progress
Build Complete!

A quiet, 8inx8in build area, Cartesian printer with permanently level bed. This is a compact, solid, inexpensive printer that will reliably print any type filament for thousands of hours while you sleep, fish, or play ball in the park.

ZideX

Feb 7, 2018
Category
Cartesian Style Bots
Build Progress
Build Complete!

3D printer with 7 drivers, compact, dual extruder, no CNC part. All Openbuilds and 3D printed part. This is purely experimental.

TrueUp Glide

Apr 14, 2017
Category
Cartesian Style Bots
Build Progress
Build Complete!

A Cartesian printer using bushings for the Z axis instead of wheels or linear bearings. The design also synchronizes two Z axis screws with a timing belt for a level lift. The ratio of the drive pulley and Z axis pulleys produce .005 lift per full step on a 200 step motor, eliminating layer resolution "drift" caused by microstepping.

MakerSL MSL-5 Cantilevered 3D Printer

Jun 23, 2016
Category
Cartesian Style Bots
Build Progress
Build in Progress...

This is a simple cantilevered 3D Printer. It is designed around the OB V-Slot linear rails. I am trying to simplify this as much as possible, all rails will be 250mm long and only one will require cutting (it will be cut in half). The printer will use all OB wheels and gantry plates where applicable, all other plates can be either Laser Cut or 3D Printed (files will be provided for both). I am not set on electronic as of yet, but plan to use a single control board...no Arduino/Ramps control.

Workhorse 3D Printer

Oct 5, 2021
Category
Cartesian Style Bots
Build Progress
Build Complete!

Large 600mm x 350mm x 350mm Build Volume with lead screw driven motion. The printer build has a moving gantry and fixed heat bed. Open Source

Bob's 3D Printer Kit Build

Apr 9, 2014
Category
Cartesian Style Bots
Build Progress
Build Complete!

I have wanted a 3D printer for a while. I had thought to convert my ShapeOko machine to a 3D printer BUT after looking at having to replace the electronics with new and the small form factor. I went looking for a kit which would do what I want. Well I found it. It is the MakerFarm i3v printer.

TrueUp Kit Version

Aug 10, 2017
Category
Cartesian Style Bots
Build Progress
Build Complete!

A Cartesian printer using bushings for the Z axis instead of wheels or linear bearings. The design also synchronizes two Z axis screws with a timing belt for a level lift. The ratio of the drive pulley and Z axis pulleys produce .005 lift per full step on a 200 step motor, eliminating layer resolution "drift" caused by microstepping.

OpenBot

Jun 3, 2014
Category
Cartesian Style Bots
Build Progress
Build in Progress...

The aim of this OpenBot build, was to make a 3d Printer that was easy to build with minimal tools and using of the shelve parts from Openbuilds.

UltiFaker 2 Go

Mar 21, 2016
Category
Cartesian Style Bots
Build Progress
Build Complete!

This is a breakdown of how I designed the UltiFaker 2 Go as well as how I machined and assembled it. I'll include a complete BOM and all of the drawings and prices.

Vulcan MAX

Feb 22, 2024
Category
Cartesian Style Bots
Build Progress
Build in Progress...

While mimicing the frame platform of the popular Crealiy CR-10 and Ender series, the Vulcan MAX overcomes design weaknesses in both printers. Chief improvements are a more stable, rigid mounting of the Z frame and Z gantry.

CubeSpawn Ultimaker 3D Printer Module

Sep 15, 2015
Category
Cartesian Style Bots
Build Progress
Build in Progress...

This 3D printer is an implementation of the Ultimaker 3D printer Using the Modular approach, many of the parts from the CubeSpawn 3 axis mill translate straight across into this design, so adding new concepts should go quicker

Adamantine

Dec 13, 2015
Category
Cartesian Style Bots
Build Progress
Build in Progress...

This is Adamantine, a all aluminum lead screw driven 3d printer. I wanted to have a printer that would not be effected by the heat or humidity I have here as my current wood frame printer is.

Black Panther QR

Mar 3, 2015
Category
Cartesian Style Bots
Build Progress
Build in Progress...

The QuadRap 3D printer version based on OpenBuilds wheels. Born in https://plus.google.com/u/0/communities/103539262895202172380

OneZ

Jan 7, 2016
Category
Cartesian Style Bots
Build Progress
Build Complete!

OneZ gets it's name from it's most unique feature - only motor for the Z axis while maintaining the stability of two bearing guides for the Z axis. Reduction to one Z motor eliminates need for auto bed leveling.

BotMaker

Nov 1, 2014
Category
Cartesian Style Bots
Build Progress
Build Complete!

This is a work in progress 3D printer Dimensions are 230x230x340mm height. Print dimensions are: 135x135x160mm. Prototype has a bowden extruder with a J-head hotend. Assembly instructions: http://reprapstyle.blogspot.pt

V Rail 3D printer

Sep 24, 2015
Category
Cartesian Style Bots
Build Progress
Build in Progress...

My version a Cartesian style 3d printer, an attempt to eliminate frame vibration and movement and to use up materials left over from other projects.

blackcat3d printer

Mar 1, 2017
Category
Cartesian Style Bots
Build Progress
Build in Progress...

in construction ! chassis vslot 80x20 & 20x20 & 60x80 (Z) home made plates with whells polycarbonate build volume environ, 750x300x200 2 ed3d v6 volcano nozzles 0.8mm & 0.6 + titan extrudeurs rumba bord + auto levelling ip camera home made heat bed aluminium 5mm + glass + heat air chamber 6 doors plexiglass......

Openbuilds V slot Rail extrusion retrofits for Lulzbot 4/5 Taz Printers (X, Y and Z axis)

Jun 20, 2016
Category
Cartesian Style Bots
Build Progress
Build Complete!

This project shows how to use Openbuilds Vv slot extrusions and wheels to retrofit a Lulzbot Taz 4 or 5 printer. These modifications improve layer consistency, eliminate nozzle and bed sag, and allow for larger toolhead mounting. Project updates and newer accessory files may be located at http://www.thingiverse.com/piercet/designs

Archer - An extendable all metal 3D printer

Jul 15, 2016
Category
Cartesian Style Bots
Build Progress
Build in Progress...

This is an all metal build using OpenBuilds V-Slot linear rails to produce a high quality and cost effective 3D printer. The printer is designed to be scalable for your desired build area and can utilize high quality hotends with 16mm groove mounts such as E3D.

SimplrBot

Jul 2, 2016
Category
Cartesian Style Bots
Build Progress
Build in Progress...

This is a simple, yet rugged design, weighing only 6 lbs and with 13x13x14" volume with a 8x8x6" build area. While assembly is pretty simple, the small size and rigidity of the design make shipping assembled printers attractive.

BldrBot Pro

Nov 13, 2014
Category
Cartesian Style Bots
Build Progress
Build in Progress...

A completely belt driven cartesian design with a center mounted X motor. This is a very compact, rugged design.

MaxBox

May 10, 2015
Category
Cartesian Style Bots
Build Progress
Build in Progress...

Simple cartesian style CNC. Uses ACME screws for all 3 axes, 20x40 v-slots and should have 50cm x 50cm x 50cm work volume.

LYNX - Huge 3D printer

Jan 14, 2016
Category
Cartesian Style Bots
Build Progress
Build in Progress...

I'm basically building a larger version of my crappy wanhao 3d printer. My work was recycling some aluminium extrusion and it broke my heart to see such nice pieces of aluminium engineering being sent to a furnace. Mega 3d printer was born!

Talos3D

Dec 10, 2015
Category
Cartesian Style Bots
Build Progress
Build Complete!

In Greek mythology, Talos (/ˈteɪlɒs/;[1] Greek: Τάλως, Talōs) was a giant man of bronze made by Hephaestus (the Greek god of fire, metalworking, craftsmen and blacksmiths) who protected Europa in Crete from pirates and invaders. He circled the island's shores three times daily.

Dash X Direct, Cross-Beam 3d Printer

Dec 18, 2022
Category
Cartesian Style Bots
Build Progress
Build Complete!

This is the next version of Dash, now operating much closer to its potential. Please message me if you need anything, such as Simplify3D settings, material information, design intent etc. Since the Pack-and-Go zip file is fairly large (120mB), here is a link where it can be downloaded: https://drive.google.com/file/d/1Q3ygyo_tTrB4UYIV62_wtCSCbWuE3krT/view?usp=sharing Note: I use Solidworks 2022, acquired through their Solidworks for Makers program (check it out!). A super deal at $100/yr

First 3d build

Dec 16, 2014
Category
Cartesian Style Bots
Build Progress
Build Complete!

I am building a simple home brewed printer. I have a background in industrial automation so I figured how hard could this be. The mechanical build was pretty smooth as was the electrical side. Now just getting plastic out the hotend is my stopping point.

STEAM crane printer

Jun 29, 2015
Category
Cartesian Style Bots
Build Progress
Build in Progress...

The STEAM Crane 3d printer uses the new C-Beam linear rail. It is being developed for an after school / summer camp program for kids. All of the electronics are housed in the base and the wiring is routed down the channels of the c-beam. This is done to contain as much of the loose wiring as possible, hopefully keeping it safer for kids.

Ez3D - Phoenix 3D Printer Build

Jun 24, 2014
Category
Cartesian Style Bots
Build Progress
Build in Progress...

This is my 1st submission to openbuilds.com and my 1st venture into building a 3D Printer. The Phoenix 3d Printer is a kit from Ez3D, a company based out of Colorado, started and backed by successful Kick-starter and IndieGogo campaigns. The Phoenix 3d Printer kit is currently backlogged 10 to 12 weeks which means quite a wait. I will be chronicling my experience with this kit as I get it done.

Makerparts.ca Prusa i3Pro 300

Mar 12, 2016
Category
Cartesian Style Bots
Build Progress
Build in Progress...

Concept for a Prusa i3 made from Cbeam Extrusion. X & Y using GT2 Belts, Z using Acme Screws Goal is to build a simple. and very Solid Printer Single Z Motor to keep the Z Screws in Sync. (Might require Geared Nema 17) 12" x 12" x 12" Build volume Nema 17's

MULIMATERIAL 3D PRINTER (in progress)

May 16, 2016
Category
Cartesian Style Bots
Build Progress
Build in Progress...

ELECTRONICS - ARDUINO Mega 2560 + RAMPS 1.4 + power supply 12V - Leadshine DM 5042 external driver + Power supply 36V + NEMA 23 stepper motor SOFTWARE - Repetier Host to communicate with the Ramps - ARDUINO to upload the firmware (Marlin) MECANIC - V-Slots rails 40x40 + home-made plates - everything goes fine on the side of the build

Versabot - All metal 3D printer

Sep 30, 2014
Category
Cartesian Style Bots
Build Progress
Build in Progress...

An all metal construction cartesian style 3D printer with a very rigid frame that has the flexibility to function as a desktop milling station or laser cutter with appropriate user designed attachments. Design is scaleable to suit any size requirement. All axis are leadscrew driven. V-Slot and Mini V-wheels have been utilised for the linear rails.

Roberta Clementine

Jun 9, 2016
Category
Cartesian Style Bots
Build Progress
Build Complete!

The Roberta Clementine a proof of concept and progenitor to the series of printers I will be calling the Clementine Sisters. The printer is named after Pittsburgh Pirates baseball player Roberto Clemente. Although it is more accurate to say the printer is named after the school I work for which is named after Clemente the Roberto Clemente Charter School. http://www.myrccs.com Roberta is the first and not really built to last but instead built to test ideas and to produce the parts for successors

BldrBox

Oct 9, 2014
Category
Cartesian Style Bots
Build Progress
Build in Progress...

OpenBuilds box type printer using min-v-wheels for X & Y axis. Designed for plexiglas panel enclosure of build area.

mBOX

Sep 25, 2016
Category
Cartesian Style Bots
Build Progress
Build in Progress...

Hi! This build is, or at least should be, a multipurpose box (mBOX). Due to limited space I want to build something that can serve multiple purposes such as 3d printing, 3d scan, plexiglass cutting and hopefully some milling too (both wood and metal). Switching between modes should involve switching heads and worksurface (change heatbed with a wood platform and viceversa). (for the scan part I'm thinking of integrating this opensource project into the frame: http://www.freelss.org/ )

TrueUp LZ

Apr 6, 2018
Category
Cartesian Style Bots
Build Progress
Build in Progress...

A version of TrueUp using linear bearings/rods for the Z axis. This required enough modification to make a separate OpenBuilds project to avoid confusion for DIYers.

Large 3D printer

Jan 7, 2016
Category
Cartesian Style Bots
Build Progress
Build in Progress...

Hello ! This is my very first OpenBuilds build. It's based on the Maximus 3D Printer, published by mytechno3d : good source of inspiration !

3D Printer 320x220x200

Sep 21, 2015
Category
Cartesian Style Bots
Build Progress
Build in Progress...

Someone donated a E3D Volcano to me (http://e3d-online.com/Volcano/V6-VOLCANO-POWER-PACK-175-UNIVERSAL-24V) and with a super hotend like that, it feels like a waste to stick it into a small 3D printer. So I decided I want a 320x220mm (XY) machine, 200mm Z is plenty for me

1.4 meter tall build height, 300x410mm build plate cartesian

Mar 26, 2017
Category
Cartesian Style Bots
Build Progress
Build in Progress...

The original plan was to build a 3d printer with a 1200x1200 build platform with a 600mm build height. I was having issues getting ahold of a large enough borosilicate glass plate for the build so I decided to go for build height. I plan on using a smoothieboard for the controller. The build has currently slowed down. I was removing a broken drillbit from the linear rail mount, and it shattered and took out my eye. I am doing what I can when I can focus my eyes long enough for the build.

RSW's 3D Printer Build

Mar 15, 2017
Category
Cartesian Style Bots
Build Progress
Build in Progress...

I recently completed my C-Beam Plate Maker build ( http://www.openbuilds.com/builds/rsws-c-beam-build.4286/ ) and quickly got the build bug. I was looking for something to make with the new C-Beam and decided its time to venture into the 3D printer world. I can honestly say I have never been in the same room with a 3D printer, so this is going to be a learning experience. I spent some time browsing the 3D printer builds and finally decided to copy the Talos3D by AlexLee.

3d nika

Jul 3, 2016
Category
Cartesian Style Bots
Build Progress
Build Complete!

Over 840 parts. Of whom around 450 are screws and nuts, more than 100 parts are printed on a 3D printer, the frame consists of about 60 components. There is nearly 40 electrical components connected with tens of meters of wires, most of them sleeved.

CoreXZ

Jan 7, 2015
Category
Cartesian Style Bots
Build Progress
Build in Progress...

I am building a H bot style printer so this design will not be finished any more than it is.

CNC/3DPrint/Laser/Mill (formerly CNC-inator3000)

Mar 5, 2018
Category
Cartesian Style Bots
Build Progress
Build in Progress...

Ultimately - the design is based on the highly successful Ultimaker concept, for which a regular size costs in the thousands, and one of this size would be edging into the 10's of thousands. Expected Build cost - <$800 It is a X/Y Cartesian printer with Raising/Lowering Z axis (Hotbed.) - Overall size is 610mm x 610mm x 750mm - with build volume of around 450mmx450mmx450mm - and will also have the ability to change work tools - such as for CNC Routing, Lazer etching, 3d Scanning, etc.

Panther Printer - Lautr3k

Oct 25, 2014
Category
Cartesian Style Bots
Build Progress
Build in Progress...

My version of the popular Lautr3k 3D printer. UNI Panther colors of Purple and Yellow on black V-slot rails. 300x300 bed.

Parthenon

Feb 2, 2015
Category
Cartesian Style Bots
Build Progress
Build in Progress...

Custom build, after building the prusa i3 and upgrading to i3v, I wanted to build something more sturdy that can print fast and more accurate. Model is built in Fusion 360

OneUpSolid

Oct 11, 2014
Category
Cartesian Style Bots
Build Progress
Build in Progress...

This is the adult version of the QU-BD juvenile known as their OneUp. It not only uses extrusion framing instead of press board MDF, it is a full sized 8x8 build area w/ABS-Nylon capability. Only the OneUp's single Z axis driver concept is similar. I'm tempted to call it OneUpAdult for marketing.

LinearRail - 3D Printer

Jan 10, 2017
Category
Cartesian Style Bots
Build Progress
Build in Progress...

I have re-purposed many of the parts from my Linear OX build. I'm using MGN 12 linear rails on all three axis, 5 start lead screws on the Z axis and I'm going to experiment with 5 start lead screw on the X axis. The frame plates are made from 1/8" laser cut mild steel, & open builds extrusion.

My first printer

Dec 13, 2017
Category
Cartesian Style Bots
Build Progress
Build Complete!

My first printer! I went for a simple cartesian design, based on evilc66 one. It uses 1000 mm C-beam linear actuators. The build volume is 700x700x700 mm^3.

Codename: Gargoyle

Jul 11, 2017
Category
Cartesian Style Bots
Build Progress
Build in Progress...

A stout 3D printer build with the hopes of being able to serve as a light mill (PCB) and laser engraver

Loading...
Loading Build images...
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice